Heat flux analysis of Type-I ELM impact on a sloped, protruding surface in the JET bulk tungsten divertor

Result code in IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61389021%3A_____%2F18%3A00507373" target="_blank" >RIV/61389021:_____/18:00507373 - isvavai.cz</a>

Result on the web

<a href="https://www.sciencedirect.com/science/article/pii/S235217911830108X?via%3Dihub" target="_blank" >https://www.sciencedirect.com/science/article/pii/S235217911830108X?via%3Dihub</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1016/j.nme.2018.10.009" target="_blank" >10.1016/j.nme.2018.10.009</a>

Result language

angličtina

Original language name

Heat flux analysis of Type-I ELM impact on a sloped, protruding surface in the JET bulk tungsten divertor

Original language description

Tungsten (W) melting due to transient power loads, for example those delivered by edge localised modes (ELMs), is a major concern for next step fusion devices. A series of experiments has been performed on JET to investigate the dynamics of Type-I ELM-induced transient melting. Following initial exposures in 2013 of a W-lamella with sharp leading edge in the bulk W outer divertor, new experiments have been performed in 2016-2017 on a protruding W-lamella with a 15 degrees slope, allowing direct and spatially resolved (0.85 mm/pixel) observation of the top surface using the IR thermography system viewing from the top of the poloidal cross-section. Thermal and IR analysis have already been conducted assuming the geometrical projection of the parallel heat flux on the W-lamellas, thus ignoring the gyro-radius orbit of plasma particles. Although it is well justified during L-mode or inter-ELM period, the hypothesis becomes questionable during ELM when the ion Larmor radius is larger. The goal of this paper is to extend the previous analysis based on the forward approach to the H-mode discharges and investigate in particular the gyro-radius effect during the Type-I ELMs, those used to achieve transient melting on the slope of the protruding W-lamella. Surface temperatures measured by the IR camera are compared with reconstructed synthetic data from 3D thermal modelling using heat loads derived from optical projection of the parallel heat flux (ignoring the gyro-radius orbit), 2D gyro-radius orbit and particle-in-cell (PIC) simulations describing the influence of finite Larmor-radius effects and electrical potential on the deposited power flux. Results show that the ELM power deposition behaves differently than the optical projection of the parallel heat flux, contrary to the L-mode observations, and may thus be due to the much larger gyro-orbits of the energetic ELM ions in comparison to L-mode or inter-ELM conditions.

Czech name

—

Czech description

—

Type

J_imp - Article in a specialist periodical, which is included in the Web of Science database

CEP classification

—

OECD FORD branch

10305 - Fluids and plasma physics (including surface physics)

Project

—

Continuities

I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Publication year

2018

Confidentiality

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Name of the periodical

Nuclear Materials and Energy

ISSN

2352-1791

e-ISSN

—

Volume of the periodical

17

Issue of the periodical within the volume

December

Country of publishing house

NL - THE KINGDOM OF THE NETHERLANDS

Number of pages

6

Pages from-to

182-187

UT code for WoS article

000454165000024

EID of the result in the Scopus database

2-s2.0-85056199780