Effect of Hot Isostatic Pressing on Porosity and Mechanical Properties of 316 L Stainless Steel Prepared by the Selective Laser Melting Method

Result code in IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F61989100%3A27230%2F20%3A10245728" target="_blank" >RIV/61989100:27230/20:10245728 - isvavai.cz</a>

Alternative codes found

RIV/68145535:_____/20:00532903 RIV/61989100:27360/20:10245728

Result on the web

<a href="https://www.mdpi.com/1996-1944/13/19/4377" target="_blank" >https://www.mdpi.com/1996-1944/13/19/4377</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/ma13194377" target="_blank" >10.3390/ma13194377</a>

Result language

angličtina

Original language name

Effect of Hot Isostatic Pressing on Porosity and Mechanical Properties of 316 L Stainless Steel Prepared by the Selective Laser Melting Method

Original language description

The manufacturing route primarily determines the properties of materials prepared by additive manufacturing methods. In this work, the microstructural features and mechanical properties of 316 L stainless steel prepared by the selective laser method have been determined. Three types of samples, (i) selective laser melted (SLM), (ii) selective laser melted and hot isostatic pressed (HIP) and (iii) selective laser melted and heat treated (HT), were characterized. Microstructural analysis revealed that SLM samples were formed by melt pool boundaries with fine cellular-dendritic-type microstructure. This type of microstructure disappeared after HT or HIP and material were formed by larger grains and sharply defined grain boundaries. The SLM-prepared samples contained different levels of porosity depending on the preparation conditions. The open interconnected LOF (lack of fusion) pores were observed in the samples, which were prepared with using of scanning speed 1200 mm/s. The blowhole and keyhole type of porosity were observed in the samples prepared by lower scanning speeds. The HIP caused a significant decrease in internal closed porosity to 0.1%, and a higher pressure of 190 MPa was more effective than the usually used pressure of 140 MPa, but for samples with open porosity, HIP was not effective. The relatively high yield strength of 570 MPa, tensile strength of 650 MPa and low ductility of 30-34% were determined for SLM samples with the lower porosity content than 1.3%. The samples after HIP showed lower yield strengths than after SLM (from 290 to 325 MPa) and relatively high ductility of 47.8-48.5%, regardless of the used SLM conditions.

Czech name

—

Czech description

—

Type

J_imp - Article in a specialist periodical, which is included in the Web of Science database

CEP classification

—

OECD FORD branch

20501 - Materials engineering

Project

<a href="/en/project/EF17_049%2F0008407" target="_blank" >EF17_049/0008407: Innovative and additive manufacturing technology - new technological solutions for 3D printing of metals and composite materials</a><br>

Continuities

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Publication year

2020

Confidentiality

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Name of the periodical

Materials

ISSN

1996-1944

e-ISSN

—

Volume of the periodical

13

Issue of the periodical within the volume

19

Country of publishing house

CH - SWITZERLAND

Number of pages

26

Pages from-to

—

UT code for WoS article

000586608500001

EID of the result in the Scopus database

2-s2.0-85093974842