Influence of long chain branching on fiber diameter distribution for polypropylene nonwovens produced by melt blown process
The result's identifiers
Result code in IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F70883521%3A28110%2F19%3A63523493" target="_blank" >RIV/70883521:28110/19:63523493 - isvavai.cz</a>
Result on the web
<a href="https://sor.scitation.org/doi/10.1122/1.5048585" target="_blank" >https://sor.scitation.org/doi/10.1122/1.5048585</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1122/1.5048585" target="_blank" >10.1122/1.5048585</a>
Alternative languages
Result language
angličtina
Original language name
Influence of long chain branching on fiber diameter distribution for polypropylene nonwovens produced by melt blown process
Original language description
In this work, linear isotactic polypropylene (L-PP) and long-chain branched polypropylene (LCB-PP) miscible blend, both having comparable weight average molecular weight, zero-shear viscosity, and polydispersity index, were used to produce nonwovens via melt blown technology in order to understand the role of long chain branching in the fiber diameter distribution. Basic morphological characteristics of produced nonwoven samples have been determined using digital image analysis of scanning electron microscope images considering different magnifications to capture nanofibers as well as microfibers. At the same air flow rate, polymer flow rate, and temperature, the average fiber diameters were the same, 1.6 μm, but the coefficient of variation, CV, was greater for the linear PP than for the blend. Material elasticity was assessed by reptation-mode relaxation time, λ, determined by fitting of deformation rate dependent shear viscosity by Cross and Carreau-Yasuda models as well as via fitting of frequency dependent loss and storage moduli master curve by a two-mode Maxwell model. It was found that λ is higher for LCB-PP in comparison with L-PP and the Cross model gives a meaningful relaxation time while the Carreau-Yasuda model does not despite giving a better numerical fit. Extensional rheology was assessed by the strain rate dependent uniaxial extensional viscosity (estimated from the entrance pressure drop using the Gibson method). The infinite shear to zero-shear shear viscosity ratio η ∞ /η 0 (obtained directly from the shear viscosity data measured in a very wide shear rate range) was shown to be proportional to the maximum normalized extensional viscosity at very high extensional strain rates, ηE, ∞ /(3η 0 ). η ∞ /η 0 was related to temperature and basic molecular characteristics of given polymers via simple equation. It was observed that extensional viscosity for both samples first decreases with increased extensional strain rate to its minimum value at 200 000-400 000 1/s and then increases to plateau value, ηE, ∞ (corresponding to the maximum chain stretch) at about 2 10 6 1/s. At low deformation rates, extensional viscosity is higher for LCB-PP in comparison with L-PP, but the trend is switched at very high deformation rates; ηE, ∞ (and also ηE, ∞ /3η 0 ) becomes lower for LCB-PP in comparison with L-PP. These results suggest that high stability of LCB-PP blend can be explained by its higher stretchability at very high deformation rates (occurring at the die exit where an intensive fiber attenuation takes the place) and its lower stretchability at medium and low deformation rates, at which melt/air inertia driven bending instability called whipping occurs.
Czech name
—
Czech description
—
Classification
Type
J<sub>imp</sub> - Article in a specialist periodical, which is included in the Web of Science database
CEP classification
—
OECD FORD branch
10404 - Polymer science
Result continuities
Project
<a href="/en/project/GA16-05886S" target="_blank" >GA16-05886S: Investigation the effect of polymer melt shear and elongational rheology on production stability of meltblown nanofibers and films</a><br>
Continuities
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Others
Publication year
2019
Confidentiality
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Data specific for result type
Name of the periodical
Journal of Rheology
ISSN
0148-6055
e-ISSN
—
Volume of the periodical
63
Issue of the periodical within the volume
4
Country of publishing house
US - UNITED STATES
Number of pages
14
Pages from-to
519-532
UT code for WoS article
000492051800002
EID of the result in the Scopus database
2-s2.0-85065595183