Filters
Effect of heat treatments with a pointed cooling on the mechanical compression properties of TiAl intermetalic
The influence of the graded cooling heat treatments on a change intermetallic were studied. The coolings were the air cooling and the graded cooling which of the differential the...
JL - Únava materiálu a lomová mechanika
- 2010 •
- D
Rok uplatnění
D - Stať ve sborníku
EFFECT OF HEAT TREATMENTS WITH A POINTED COOLING ON THE MECHANICAL COMPRESSION PROPERTIES OF TiAl INTERMETALIC
The influence of the graded cooling heat treatments on a change intermetallic were studied. The used heat treatments were consisting from heating and the graded cooling ...
JG - Hutnictví, kovové materiály
- 2010 •
- D
Rok uplatnění
D - Stať ve sborníku
Microstructure Characterization and Faigue Behavior of Beta Phase Containing Gama-TiAl Alloy
The microstructure and fatigue properties of Ti?44Al?7.8Nb ? 0.2Ni (at.%) alloy after graded cooling heat treatment were investigated. Different techniques as SEM of phase volume fraction was measured by neutron di...
JG - Hutnictví, kovové materiály
- 2012 •
- D
Rok uplatnění
D - Stať ve sborníku
Improvement of S355J2 Steel Mechanical Properties by Heat Treatment
Steel grade S355J2 (1.0577) is standard carbon steel which is commonly used in building engineering. The Heat Transfer and Fluid Flow Laboratory is equipped by a testing device called Karusel. It enables to simulate heat
JG - Hutnictví, kovové materiály
- 2016 •
- O
Rok uplatnění
O - Ostatní výsledky
Determination of Temperature Dependent Cooling Intensity for the Simulation of In-line Heat Treatment
on the chemical composition but also on the cooling process after rolling. This article concerns the simulation of heat treatment of steel products during the in-line process steel grades. However, for these simul...
JG - Hutnictví, kovové materiály
- 2013 •
- D •
- Link
Rok uplatnění
D - Stať ve sborníku
Výsledek na webu
Cooling system for heat treatment of thick sheets
The cooling collectors for heat treatment of thick sheets were designed based on a series of laboratory tests using various types of cooling nozzles and different cooling configurations as well. The collec...
JG - Hutnictví, kovové materiály
- 2015 •
- Ztech
Rok uplatnění
Ztech - Ověřená technologie
Heat Transfer in the Primary Cooling Zone of a Continuous Casting Me For Steel
task of primary cooling is primarily the heat dissipation fromsolidifying steel of the heat flux density between thesteel and the cooling water in the mould were expressed in the primary cooling area. For...
Materials engineering
- 2024 •
- D •
- Link
Rok uplatnění
D - Stať ve sborníku
Výsledek na webu
Experimental study of in-line heat treatment of 1.0577 structural steel
In-line heat treatment is frequently used in rolling mills because it offers of additional alloying and rolled product reheating. Disadvantage of in-line heat treatment system which allows keeping required cool...
Thermodynamics
- 2018 •
- D •
- Link
Rok uplatnění
D - Stať ve sborníku
Výsledek na webu
Heat treatment of tubes
for the design of the cooling sections which can obtain a desired heat treatment procedureThis paper describes a design procedure of cooling sections for the heat treatment of tubes. Two experime...
JG - Hutnictví, kovové materiály
- 2015 •
- D
Rok uplatnění
D - Stať ve sborníku
Mechanical Properties of Steel AISI 4135 after Three Different Experimental Heat Treatment Procedures for the High Pressure Cylinders Production
was applied. Three types of different variants of heat treatment with controlled accelerated cooling were used leading to different segregation banding, combinations favourable variant of heat treatment s...
JG - Hutnictví, kovové materiály
- 2015 •
- Jx
Rok uplatnění
Jx - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
- 1 - 10 out of 118 271