Filters
Mathematische Modellierung von den Werkzeugmaschinenspindeln
The paper describes modelling of machine tools by FEM-methods. The new Dynast-Library-Elements are basic elements for modelling of spindle geometry. There is possible to model spindle statics or spindl...
JQ - Strojní zařízení a nástroje
- 2004 •
- D
Rok uplatnění
D - Stať ve sborníku
Mathematische Modellierung von den Werkzeugmaschinenspindeln
The paper describes modelling of machine tools by FEM-methods. The new Dynast-Library-Elements are basic elements for modelling of spindle geometry. There is possible to model spindle statics or spindl...
JQ - Strojní zařízení a nástroje
- 2004 •
- D
Rok uplatnění
D - Stať ve sborníku
Mathematische Modellierung von den Werkzeugmaschinenspindeln
The paper describes modelling of machine tools by FEM-methods. The new Dynast-Library-Elements are basic elements for modelling of spindle geometry. There is possible to model spindle statics or spindl...
JQ - Strojní zařízení a nástroje
- 2004 •
- D
Rok uplatnění
D - Stať ve sborníku
Modeling of spindle of the machine SpeedTec. Part 1: Spindle model and experimental tests.
The report describes preliminary measuring of dynamical properties of spindle of the machine SpeedTec. The requirements to interconnected model of spindle and machine are defined according to these measurements. The spi...
JQ - Strojní zařízení a nástroje
- 2008 •
- O
Rok uplatnění
O - Ostatní výsledky
Dynamical properties od machine tool spindles
The report describes measurement and modeling of spindles of Tajmac-ZPS company. Measurements on free spindles and also on spindles built in machine are described. Models of mechanical and thermo-mechanica...
JQ - Strojní zařízení a nástroje
- 2009 •
- O
Rok uplatnění
O - Ostatní výsledky
Introduction to the Methodics of Spindles - Spindle Stocks Coupled
The report describes creation of the spindle - spindle stock coupled model. The model is used for analysis of the spindle stock influence to spindle dynamical properties....
JQ - Strojní zařízení a nástroje
- 2007 •
- O
Rok uplatnění
O - Ostatní výsledky
Matematical Model of a Spindle and Its Verification
The paper describes the modelling of machine tools spindles in solver Dynast. New user-defined elements were created for this modelling. Models for statics matrixK for element with three DOF for modelling ...
JQ - Strojní zařízení a nástroje
- 2004 •
- D
Rok uplatnění
D - Stať ve sborníku
Modeling of machine tools spindle in Dynast
The paper describes modeling of machine tools spindle in Dynast. The stifness matrix K and the mass matrix M create the ground element of Dynast element-library. There is possible with this elements to model geometry of
JQ - Strojní zařízení a nástroje
- 2003 •
- D
Rok uplatnění
D - Stať ve sborníku
Modelling of Machine Tools Spindles
The report gives informations about building of heavy model of spindle. This model is verificated with an experimental measuring. This model is used for dedication of importand features of general spindle ...
JQ - Strojní zařízení a nástroje
- 2005 •
- O
Rok uplatnění
O - Ostatní výsledky
Prediction of Machine Tool Spindle's Dynamics Based on a Thermo-Mechanical Model
This paper presents a thermo-mechanical model of spindles with rolling bearings. Thermal deformation due to spindle internal heat sources affects significantly in predictive models of spindles' dynamics. T...
JQ - Strojní zařízení a nástroje
- 2010 •
- Jx
Rok uplatnění
Jx - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
- 1 - 10 out of 169 737