Measurement of gauge blocks by interferometry

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00177016%3A_____%2F16%3A%230001221" target="_blank" >RIV/00177016:_____/16:#0001221 - isvavai.cz</a>

Výsledek na webu

<a href="http://stacks.iop.org/0026-1394/53/i=1A/a=04003?key=crossref.610b986750827900c0c10edf8d79e5a8" target="_blank" >http://stacks.iop.org/0026-1394/53/i=1A/a=04003?key=crossref.610b986750827900c0c10edf8d79e5a8</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1088/0026-1394/53/1A/04003" target="_blank" >10.1088/0026-1394/53/1A/04003</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Measurement of gauge blocks by interferometry

Popis výsledku v původním jazyce

The metrological equivalence of national measurement standards will be determined by a set of key comparisons chosen and organized by the Consultative Committees of the CIPM working closely with the Regional Metrology Organizations (RMOs). At its meetingin September 2008, the Consultative Committee for Length, CCL, identified several key comparisons in the field of dimensional metrology. In particular, it decided that the formally individual key comparisons on short gauge blocks and on length bars (long gauge blocks) should be combined under the designation CCL-K1. The key comparison detailed in this document, EURAMET.L-K1.2011, is parallel to the CIPM key comparison CCL-K1.2011 which is piloted by CENAM and NRC. Key Comparison EURAMET.L-K1 was instigated following a decision at the 2010 meeting of the EURAMET Length contact persons held at SP Technical Research Institute of Sweden. The sets of gauge blocks used in both the CCL and EURAMET key comparisons have almost the same composit

Název v anglickém jazyce

Measurement of gauge blocks by interferometry

Popis výsledku anglicky

The metrological equivalence of national measurement standards will be determined by a set of key comparisons chosen and organized by the Consultative Committees of the CIPM working closely with the Regional Metrology Organizations (RMOs). At its meetingin September 2008, the Consultative Committee for Length, CCL, identified several key comparisons in the field of dimensional metrology. In particular, it decided that the formally individual key comparisons on short gauge blocks and on length bars (long gauge blocks) should be combined under the designation CCL-K1. The key comparison detailed in this document, EURAMET.L-K1.2011, is parallel to the CIPM key comparison CCL-K1.2011 which is piloted by CENAM and NRC. Key Comparison EURAMET.L-K1 was instigated following a decision at the 2010 meeting of the EURAMET Length contact persons held at SP Technical Research Institute of Sweden. The sets of gauge blocks used in both the CCL and EURAMET key comparisons have almost the same composit

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JB - Senzory, čidla, měření a regulace

OECD FORD obor

—

Projekt

—

Návaznosti

V - Vyzkumna aktivita podporovana z jinych verejnych zdroju

Rok uplatnění

2016

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Metrologia

ISSN

0026-1394

e-ISSN

—

Svazek periodika

53

Číslo periodika v rámci svazku

1A

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

63

Strana od-do

1-63

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—