Effect of hydrogen on formation of Fe-Al nanoparticles by mechanical milling

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216208%3A11320%2F14%3A10290408" target="_blank" >RIV/00216208:11320/14:10290408 - isvavai.cz</a>

Výsledek na webu

<a href="http://www.scientific.net/JNanoR.29.23" target="_blank" >http://www.scientific.net/JNanoR.29.23</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/JNanoR.29.23" target="_blank" >10.4028/www.scientific.net/JNanoR.29.23</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Effect of hydrogen on formation of Fe-Al nanoparticles by mechanical milling

Popis výsledku v původním jazyce

Nanocrystalline powders of iron aluminum alloy of the Fe82Al18 nominal composition were prepared under air, hydrogen and nitrogen atmospheres from the Fe and Al elemental powders by mechanical alloying and also from the conventionally cast Fe82Al18 alloyby the high-energy ball milling. The intensive plastic deformation during high-energy mechanical treatment has introduced high concentrations of open volume defects and contributed to a rapid decrease in the crystallite size down to a nanoscopic range.The hydrogen atmosphere was found to be the most efficient for the Fe-Al mechanical alloying since it has resulted into the fully alloyed Fe82Al18 after 30 h of milling. On the other hand, the nitrogen and air atmosphere have slightly prevented mechanical alloying and after the same milling time the pure iron particles were still detected in the powder mixtures. This partial suppression of the mechanical alloying process is explained by a formation of thin iron nitride and/or oxide layer

Název v anglickém jazyce

Effect of hydrogen on formation of Fe-Al nanoparticles by mechanical milling

Popis výsledku anglicky

Nanocrystalline powders of iron aluminum alloy of the Fe82Al18 nominal composition were prepared under air, hydrogen and nitrogen atmospheres from the Fe and Al elemental powders by mechanical alloying and also from the conventionally cast Fe82Al18 alloyby the high-energy ball milling. The intensive plastic deformation during high-energy mechanical treatment has introduced high concentrations of open volume defects and contributed to a rapid decrease in the crystallite size down to a nanoscopic range.The hydrogen atmosphere was found to be the most efficient for the Fe-Al mechanical alloying since it has resulted into the fully alloyed Fe82Al18 after 30 h of milling. On the other hand, the nitrogen and air atmosphere have slightly prevented mechanical alloying and after the same milling time the pure iron particles were still detected in the powder mixtures. This partial suppression of the mechanical alloying process is explained by a formation of thin iron nitride and/or oxide layer

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

BM - Fyzika pevných látek a magnetismus

OECD FORD obor

—

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach<br>I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2014

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Journal of Nano Research

ISSN

1662-5250

e-ISSN

—

Svazek periodika

29

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

6

Strana od-do

23-28

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—