The role of alpha '' orthorhombic phase content on the tenacity and fracture toughness behavior of Ti-22Nb-10Zr coating used in the design of long-term medical implants

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216208%3A11320%2F19%3A10405473" target="_blank" >RIV/00216208:11320/19:10405473 - isvavai.cz</a>

Výsledek na webu

<a href="https://verso.is.cuni.cz/pub/verso.fpl?fname=obd_publikace_handle&handle=AfbSQOHgzu" target="_blank" >https://verso.is.cuni.cz/pub/verso.fpl?fname=obd_publikace_handle&handle=AfbSQOHgzu</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1016/j.apsusc.2018.09.017" target="_blank" >10.1016/j.apsusc.2018.09.017</a>

Jazyk výsledku

angličtina

Název v původním jazyce

The role of alpha '' orthorhombic phase content on the tenacity and fracture toughness behavior of Ti-22Nb-10Zr coating used in the design of long-term medical implants

Popis výsledku v původním jazyce

Tenacity and fracture toughness of a novel beta/alpha &apos;&apos; Ti-22Nb-10Zr (wt.%) coating processed by magnetron sputtering were modified as a result of the martensitic transformation (beta -&gt; alpha &apos;&apos;) activated by the presence of compressive residual stresses when the coating deposition is performed at high bias voltage values. Mechanical properties, such as hardness, H, and Young&apos;s modulus, E, values, and therefore elastoplastic response of the coating were characterized through H/E, and H-3/E-2 ratios as a function of the extent of the martensitic transformation. These ratios were correlated to the elastic response and to the resistance to plastic deformation of a surface subjected to sliding mechanical contact, respectively. The usefulness of both ratios to design &quot;hard and tough&quot; coatings, suitable for enhancing of its wear resistance, is compared with the tenacity, G, the semiquantitative, FT, and the quantitative, K-I, fracture toughness values obtained from nano-scratch characterization. Results show that Ti-22Nb-10Zr (wt.%) coating with the highest and lowest hardness and Young&apos;s modulus values, and therefore the highest H/E and H-3/E-2, has the highest cracking resistance and fracture toughness. Under linearly ramped loading from 0.1 to 5 and 100 mN it was impossible to produce fracture of the coating when it was deposited with a bias voltage of -63 V. In return, the coating deposited with a bias voltage of - 148 V shows an almost complete elastic recovery until the moment of its fracture and delamination, which is an evidence of its high tenacity and superior fracture toughness. The K-I value is similar to 21 MPa*m(1/2), which is higher than typical values of bio-ceramics (Al2O3 and ZrO2) used in medical applications, demonstrating that this coating could be used in components subjected to high wear and cyclic impacts, e.g. on femoral heads in artificial hip joints.

Název v anglickém jazyce

The role of alpha '' orthorhombic phase content on the tenacity and fracture toughness behavior of Ti-22Nb-10Zr coating used in the design of long-term medical implants

Popis výsledku anglicky

Tenacity and fracture toughness of a novel beta/alpha &apos;&apos; Ti-22Nb-10Zr (wt.%) coating processed by magnetron sputtering were modified as a result of the martensitic transformation (beta -&gt; alpha &apos;&apos;) activated by the presence of compressive residual stresses when the coating deposition is performed at high bias voltage values. Mechanical properties, such as hardness, H, and Young&apos;s modulus, E, values, and therefore elastoplastic response of the coating were characterized through H/E, and H-3/E-2 ratios as a function of the extent of the martensitic transformation. These ratios were correlated to the elastic response and to the resistance to plastic deformation of a surface subjected to sliding mechanical contact, respectively. The usefulness of both ratios to design &quot;hard and tough&quot; coatings, suitable for enhancing of its wear resistance, is compared with the tenacity, G, the semiquantitative, FT, and the quantitative, K-I, fracture toughness values obtained from nano-scratch characterization. Results show that Ti-22Nb-10Zr (wt.%) coating with the highest and lowest hardness and Young&apos;s modulus values, and therefore the highest H/E and H-3/E-2, has the highest cracking resistance and fracture toughness. Under linearly ramped loading from 0.1 to 5 and 100 mN it was impossible to produce fracture of the coating when it was deposited with a bias voltage of -63 V. In return, the coating deposited with a bias voltage of - 148 V shows an almost complete elastic recovery until the moment of its fracture and delamination, which is an evidence of its high tenacity and superior fracture toughness. The K-I value is similar to 21 MPa*m(1/2), which is higher than typical values of bio-ceramics (Al2O3 and ZrO2) used in medical applications, demonstrating that this coating could be used in components subjected to high wear and cyclic impacts, e.g. on femoral heads in artificial hip joints.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

10302 - Condensed matter physics (including formerly solid state physics, supercond.)

Projekt

<a href="/cs/project/EF15_003%2F0000485" target="_blank" >EF15_003/0000485: Centrum nanomateriálů pro pokročilé aplikace</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Applied Surface Science

ISSN

0169-4332

e-ISSN

—

Svazek periodika

464

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

NL - Nizozemsko

Počet stran výsledku

9

Strana od-do

328-336

Kód UT WoS článku

000447744200039

EID výsledku v databázi Scopus

2-s2.0-85053317840