Industrial Corona Pre- and Post-treatment for Enhanced Silicone Coating of Paper used as Release Liner

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216224%3A14310%2F18%3A00114984" target="_blank" >RIV/00216224:14310/18:00114984 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/00216224:14310/17:00097987

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Industrial Corona Pre- and Post-treatment for Enhanced Silicone Coating of Paper used as Release Liner

Popis výsledku v původním jazyce

In this work, atmospheric pressure, ambient air plasma was used for pre-treatment of clay coated paper before silicone coating as well as for post-treatment to prepare the release liner with low adhesion. As a plasma source “industrial corona” in roll-to-roll configuration was used for plasma treatment. The aim of the study was to evaluate the effect of plasma pre- and post-treatment time on adhesive properties of silicone layer sprayed on the paper. Plasma pre-treated paper was sprayed with silicone oil of different amounts using spray gun and subsequently plasma post-treated for defined repetition. Surface of silicone sprayed paper was analyzed by water contact angle measurement immediately after oil spraying procedure. The possible changes in morphology were characterized by scanning electron microscopy, chemical composition by X-ray photoelectron spectroscopy and the adhesion by measuring tape peel force. The silicone coated paper was characterized by increase of hydrophobicity and decrease of release factor with significant impact of plasma post-treatment.

Název v anglickém jazyce

Industrial Corona Pre- and Post-treatment for Enhanced Silicone Coating of Paper used as Release Liner

Popis výsledku anglicky

In this work, atmospheric pressure, ambient air plasma was used for pre-treatment of clay coated paper before silicone coating as well as for post-treatment to prepare the release liner with low adhesion. As a plasma source “industrial corona” in roll-to-roll configuration was used for plasma treatment. The aim of the study was to evaluate the effect of plasma pre- and post-treatment time on adhesive properties of silicone layer sprayed on the paper. Plasma pre-treated paper was sprayed with silicone oil of different amounts using spray gun and subsequently plasma post-treated for defined repetition. Surface of silicone sprayed paper was analyzed by water contact angle measurement immediately after oil spraying procedure. The possible changes in morphology were characterized by scanning electron microscopy, chemical composition by X-ray photoelectron spectroscopy and the adhesion by measuring tape peel force. The silicone coated paper was characterized by increase of hydrophobicity and decrease of release factor with significant impact of plasma post-treatment.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

10305 - Fluids and plasma physics (including surface physics)

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2018

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

9th International Conference on Nanomaterials - Reseach & Application (NANOCON)

ISBN

9788087294819

ISSN

—

e-ISSN

—

Počet stran výsledku

6

Strana od-do

271-276

Název nakladatele

TANGER Ltd., Ostrava

Místo vydání

Brno

Místo konání akce

Brno

Datum konání akce

1. 1. 2017

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

000452823300045