Wooden Facade and Determination of Strength of Bonded Timber Joints

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26110%2F14%3APU111674" target="_blank" >RIV/00216305:26110/14:PU111674 - isvavai.cz</a>

Výsledek na webu

<a href="http://arsa-conf.com/archive/?vid=1&aid=2&kid=60301-72" target="_blank" >http://arsa-conf.com/archive/?vid=1&aid=2&kid=60301-72</a>

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Wooden Facade and Determination of Strength of Bonded Timber Joints

Popis výsledku v původním jazyce

A research case focused on vented wooden façade system with bonded joints is presented in this paper. The potential of bonded joints is studied and described in more detail and verified through experimental measurements. For the purpose of tests spruce timber profiles were chosen for the load bearing substructure and Wooden plastic composite façade sheeting for the cladding. Three types of industrial adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent experimental verification of substructure bonding retention to the cladding. The adhesive bonds were tested both in tension as well as in shear at a temperature of (293.15+/-3) K and a relative humidity of (55+/-10) %. The test results proved the fact that bonded joints are more than suitable alternative to the mechanical joints. During the tests appeared some differences in stability and failure behaviour between the adhesive systems as well as within the sheeting material. Additionally, the suitability of selected group of adhesives in combination with wooden plastic cladding material as well as with the timber substructure was confirmed.

Název v anglickém jazyce

Wooden Facade and Determination of Strength of Bonded Timber Joints

Popis výsledku anglicky

A research case focused on vented wooden façade system with bonded joints is presented in this paper. The potential of bonded joints is studied and described in more detail and verified through experimental measurements. For the purpose of tests spruce timber profiles were chosen for the load bearing substructure and Wooden plastic composite façade sheeting for the cladding. Three types of industrial adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent experimental verification of substructure bonding retention to the cladding. The adhesive bonds were tested both in tension as well as in shear at a temperature of (293.15+/-3) K and a relative humidity of (55+/-10) %. The test results proved the fact that bonded joints are more than suitable alternative to the mechanical joints. During the tests appeared some differences in stability and failure behaviour between the adhesive systems as well as within the sheeting material. Additionally, the suitability of selected group of adhesives in combination with wooden plastic cladding material as well as with the timber substructure was confirmed.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20101 - Civil engineering

Projekt

<a href="/cs/project/FR-TI4%2F332" target="_blank" >FR-TI4/332: Nové technologie lepených obvodových plášťů budov s kotvícími prvky se zvýšenou odolností vůči korozi</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2014

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Proceedings in Advanced Research in Scientific Areas (ARSA 2014)

ISBN

978-80-554-0958-0

ISSN

1338-9831

e-ISSN

—

Počet stran výsledku

5

Strana od-do

331-335

Název nakladatele

EDIS - Publishing Institution of the University of Zilina

Místo vydání

Žilina

Místo konání akce

Žilina

Datum konání akce

1. 12. 2014

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—