Utilization of Waste Packaging Glass as Progressive Filler in Polymer Anchor Material Based on Epoxy Resin

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26110%2F19%3APU125643" target="_blank" >RIV/00216305:26110/19:PU125643 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.scientific.net/AMM.887.40" target="_blank" >https://www.scientific.net/AMM.887.40</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/AMM.887.40" target="_blank" >10.4028/www.scientific.net/AMM.887.40</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Utilization of Waste Packaging Glass as Progressive Filler in Polymer Anchor Material Based on Epoxy Resin

Popis výsledku v původním jazyce

The work deals with the use of waste glass to the polymer anchor material based on epoxy resin, primarily for anchoring to a high strength concrete (HSC). The main aim was to use the largest possible amount of the waste packaging glass by reducing the amount of epoxy resin, which is an expensive material and its production has a negative impact on the environment. Within the experimental verification, the influence of waste packaging glass fraction 0–0.63 mm on the final properties of the polymer anchoring material was observed. To determine the optimal formulation compressive strength, flexural strength, chemical resistance, shrinkage and pull-out test were performed. Based on the evaluation of the results the optimal percentage of filling was determined, when the polymer anchor material showed high strengths, minimal shrinkage, good chemical resistance, optimal consistency for anchoring into the HSC and high anchor bolt pull-out strength.

Název v anglickém jazyce

Utilization of Waste Packaging Glass as Progressive Filler in Polymer Anchor Material Based on Epoxy Resin

Popis výsledku anglicky

The work deals with the use of waste glass to the polymer anchor material based on epoxy resin, primarily for anchoring to a high strength concrete (HSC). The main aim was to use the largest possible amount of the waste packaging glass by reducing the amount of epoxy resin, which is an expensive material and its production has a negative impact on the environment. Within the experimental verification, the influence of waste packaging glass fraction 0–0.63 mm on the final properties of the polymer anchoring material was observed. To determine the optimal formulation compressive strength, flexural strength, chemical resistance, shrinkage and pull-out test were performed. Based on the evaluation of the results the optimal percentage of filling was determined, when the polymer anchor material showed high strengths, minimal shrinkage, good chemical resistance, optimal consistency for anchoring into the HSC and high anchor bolt pull-out strength.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20101 - Civil engineering

Projekt

<a href="/cs/project/TA04010425" target="_blank" >TA04010425: Komplexní systém speciálních správkových hmot s využitím druhotných surovin pro průmyslové provozy</a><br>

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

12th Envibuild – Buildings and Environment – From Research to Application

ISBN

978-3-0357-1202-5

ISSN

1660-9336

e-ISSN

—

Počet stran výsledku

8

Strana od-do

40-47

Název nakladatele

Trans Tech Publications

Místo vydání

Switzerland

Místo konání akce

Vídeň

Datum konání akce

7. 9. 2017

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—