Effect of Imposed Shear Strain on Steel Ring Surfaces during Milling in High‐Speed Disintegrator

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26110%2F20%3APU136466" target="_blank" >RIV/00216305:26110/20:PU136466 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mdpi.com/1996-1944/13/10/2234" target="_blank" >https://www.mdpi.com/1996-1944/13/10/2234</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/ma13102234" target="_blank" >10.3390/ma13102234</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Effect of Imposed Shear Strain on Steel Ring Surfaces during Milling in High‐Speed Disintegrator

Popis výsledku v původním jazyce

This contribution characterizes the performance of a DESI 11 high‐speed disintegrator working on the principle of a pin mill with two opposite counter‐rotating rotors. As the ground material, batches of Portland cement featuring 6–7 Mohs scale hardness and containing relatively hard and abrasive compounds with the specific surface areas ranging from 200 to 500 m2/kg, with the step of 50 m2/kg, were used. The character of the ground particles was assessed via scanning electron microscopy and measurement of the absolute/relative increase in their specific surface areas. Detailed characterization of the rotors was performed via recording the thermal imprints, evaluating their wear by 3D optical microscopy, and measuring rotor weight loss after the grinding of constant amounts of cement. The results showed that coarse particles are ground by impacting the front faces of the pins, while finer particles are primarily milled via mutual collisions. Therefore, the coarse particles cause higher abrasion and wear on the rotor pins; after the milling of 20 kg of the 200 m2/kg cement sample, the wear of the rotor reached up to 5% of its original mass and the pins were severely damaged.

Název v anglickém jazyce

Effect of Imposed Shear Strain on Steel Ring Surfaces during Milling in High‐Speed Disintegrator

Popis výsledku anglicky

This contribution characterizes the performance of a DESI 11 high‐speed disintegrator working on the principle of a pin mill with two opposite counter‐rotating rotors. As the ground material, batches of Portland cement featuring 6–7 Mohs scale hardness and containing relatively hard and abrasive compounds with the specific surface areas ranging from 200 to 500 m2/kg, with the step of 50 m2/kg, were used. The character of the ground particles was assessed via scanning electron microscopy and measurement of the absolute/relative increase in their specific surface areas. Detailed characterization of the rotors was performed via recording the thermal imprints, evaluating their wear by 3D optical microscopy, and measuring rotor weight loss after the grinding of constant amounts of cement. The results showed that coarse particles are ground by impacting the front faces of the pins, while finer particles are primarily milled via mutual collisions. Therefore, the coarse particles cause higher abrasion and wear on the rotor pins; after the milling of 20 kg of the 200 m2/kg cement sample, the wear of the rotor reached up to 5% of its original mass and the pins were severely damaged.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20101 - Civil engineering

Projekt

<a href="/cs/project/GA20-00676S" target="_blank" >GA20-00676S: Vliv mechano-chemické aktivace na proces vzniku, strukturu a stabilitu vybraných slínkových minerálů</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2020

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials

ISSN

1996-1944

e-ISSN

—

Svazek periodika

13

Číslo periodika v rámci svazku

10

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

12

Strana od-do

10-22

Kód UT WoS článku

000539277000026

EID výsledku v databázi Scopus

2-s2.0-85085249684