3D scanning as an effective tool for controlling the dimensions of test specimens

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26110%2F23%3APU146768" target="_blank" >RIV/00216305:26110/23:PU146768 - isvavai.cz</a>

Výsledek na webu

<a href="http://tces.vsb.cz/Home/ArticleDetail/844" target="_blank" >http://tces.vsb.cz/Home/ArticleDetail/844</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.35181/tces-2022-0014" target="_blank" >10.35181/tces-2022-0014</a>

Jazyk výsledku

angličtina

Název v původním jazyce

3D scanning as an effective tool for controlling the dimensions of test specimens

Popis výsledku v původním jazyce

3D laser scanning is a powerfull tool that digitally captures the shape of physical objects using a laser light crosses. In this work, the 3D laser scanning technology is used for the 3D shape capture of specially designed specimens. These specimens previously made of fine-grained cement-based composite of the nominal dimensions 40 × 40 × 160 mm with inclusion in the shape of prisms with nominal dimensions of 8 × 8 × 40 mm were provided with an initial central edge notch and tested in the three-point bending configuration. The aim of this paper is to study the macrostructure of fracture surfaces via 3D scanning technology, measure the area of ligament, verify the designed notch depth and evaluate the fracture toughness and specific fracture energy based on the measured dimensions. The results indicate that the measured notch depth is lower than the designed one thus the differences between fracture toughness calculated for designed notch depth and for the measured one is approximately 10 %. In addition, the fracture toughness is overestimated when considering the design values.

Název v anglickém jazyce

3D scanning as an effective tool for controlling the dimensions of test specimens

Popis výsledku anglicky

3D laser scanning is a powerfull tool that digitally captures the shape of physical objects using a laser light crosses. In this work, the 3D laser scanning technology is used for the 3D shape capture of specially designed specimens. These specimens previously made of fine-grained cement-based composite of the nominal dimensions 40 × 40 × 160 mm with inclusion in the shape of prisms with nominal dimensions of 8 × 8 × 40 mm were provided with an initial central edge notch and tested in the three-point bending configuration. The aim of this paper is to study the macrostructure of fracture surfaces via 3D scanning technology, measure the area of ligament, verify the designed notch depth and evaluate the fracture toughness and specific fracture energy based on the measured dimensions. The results indicate that the measured notch depth is lower than the designed one thus the differences between fracture toughness calculated for designed notch depth and for the measured one is approximately 10 %. In addition, the fracture toughness is overestimated when considering the design values.

Druh

J_ost - Ostatní články v recenzovaných periodicích

CEP obor

—

OECD FORD obor

20101 - Civil engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2023

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Transactions of the VŠB – Technical University of Ostrava, Civil Engineering Series

ISSN

1804-4824

e-ISSN

—

Svazek periodika

22

Číslo periodika v rámci svazku

2

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

7

Strana od-do

45-50

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—