THE HEAT TRANSFER COEFFICIENT AT DISCONTINUED WATER SPRAY COOLING

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F15%3APU114301" target="_blank" >RIV/00216305:26210/15:PU114301 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

THE HEAT TRANSFER COEFFICIENT AT DISCONTINUED WATER SPRAY COOLING

Popis výsledku v původním jazyce

Cooling by water sprays is widely used in heat treatment and other metallurgical processes to control the process temperature. Water spray cooling is used statically (without movement of the spray nozzles relative to the cooled object) or dynamically (with the movement). The static regime is typical for quenching systems intended for heat treatment of fixed steel plates. The dynamic regime is used in steel treatment processes such as rolling and finishing in mills. The movement of the steel plate relative to the fixed cooling section causes non-homogeneous distribution of water on the surface of the steel plate. The variability of the cooling section length, position of water nozzles and non-homogeneity of water distribution lead to non-uniform and distorted cooling conditions. Thus it is an important issue to define the impact of these parameters on cooling intensity and the heat transfer coefficient during the cooling process of steel plates. Heat treatment of hightemperature steel is held without protective atmosphere and is accompanied by growth of different oxides on the steel plate surface as well. The layer of oxides significantly affects the cooling regime and intensity. The influence of the oxide scales on the cooling intensity was studied experimentally and by numerical modeling for different cooling regimes. Experiments were conducted for static and dynamic regimes on surfaces with different rate of oxides layer. Prepared numerical analysis simulates the process with different conditions of the cooling section and samples with different oxide scale layers. Results obtained by numerical simulation approved the impact of the oxide layer on the cooling intensity and shown different character in the static and the dynamic regime.

Název v anglickém jazyce

THE HEAT TRANSFER COEFFICIENT AT DISCONTINUED WATER SPRAY COOLING

Popis výsledku anglicky

Cooling by water sprays is widely used in heat treatment and other metallurgical processes to control the process temperature. Water spray cooling is used statically (without movement of the spray nozzles relative to the cooled object) or dynamically (with the movement). The static regime is typical for quenching systems intended for heat treatment of fixed steel plates. The dynamic regime is used in steel treatment processes such as rolling and finishing in mills. The movement of the steel plate relative to the fixed cooling section causes non-homogeneous distribution of water on the surface of the steel plate. The variability of the cooling section length, position of water nozzles and non-homogeneity of water distribution lead to non-uniform and distorted cooling conditions. Thus it is an important issue to define the impact of these parameters on cooling intensity and the heat transfer coefficient during the cooling process of steel plates. Heat treatment of hightemperature steel is held without protective atmosphere and is accompanied by growth of different oxides on the steel plate surface as well. The layer of oxides significantly affects the cooling regime and intensity. The influence of the oxide scales on the cooling intensity was studied experimentally and by numerical modeling for different cooling regimes. Experiments were conducted for static and dynamic regimes on surfaces with different rate of oxides layer. Prepared numerical analysis simulates the process with different conditions of the cooling section and samples with different oxide scale layers. Results obtained by numerical simulation approved the impact of the oxide layer on the cooling intensity and shown different character in the static and the dynamic regime.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20303 - Thermodynamics

Projekt

<a href="/cs/project/LO1202" target="_blank" >LO1202: NETME CENTRE PLUS</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2015

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

METAL 2015, 24rd International Conference on Metallurgy and Materials, Conference Proceedings

ISBN

978-80-87294-58-1

ISSN

—

e-ISSN

—

Počet stran výsledku

6

Strana od-do

1-6

Název nakladatele

TANGER

Místo vydání

Ostrava

Místo konání akce

Brno

Datum konání akce

3. 6. 2015

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

000374706100013