Investigation of the Influence of PVD Coatings Deposited on HSS Milling Cutter
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F16%3APU119695" target="_blank" >RIV/00216305:26210/16:PU119695 - isvavai.cz</a>
Výsledek na webu
<a href="http://journal.strojirenskatechnologie.cz/templates/obalky_casopis/XVI_2016-3.pdf" target="_blank" >http://journal.strojirenskatechnologie.cz/templates/obalky_casopis/XVI_2016-3.pdf</a>
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Investigation of the Influence of PVD Coatings Deposited on HSS Milling Cutter
Popis výsledku v původním jazyce
This article deals with the benefits of PVD coatings ((Al,Ti)N; (Al,Ti,Cr)N and nanocomposite coating nACo®) applied to HSS three edges end milling cutters (producer ZPS – Frezovaci nastroje, Zlin, CZ). The coatings were synthesized by a cathodic-arc deposition process (producer Liss, Roznov pod Radhostem, CZ). Machining was carried out on the vertical milling machine FB 32V with using process liquid. Set up cutting conditions were con-stant throughout the machining. The aim of this experiment was to compare coated and uncoated HSS end milling cutters and find out the benefits of three kinds of PVD coatings. The monitored parameters were force loading and flank wear. Piezoeletrical dynamometer Kistler 9257B was used for measuring force loading and workshop opti-cal microscope was used for measuring flank wear (criterion VB). The construction steel C45E (1.1191; CSN 41 2050) was used as workpiece material. Best results were achieved by tool with PVD coating (Al,Ti,Cr)N.
Název v anglickém jazyce
Investigation of the Influence of PVD Coatings Deposited on HSS Milling Cutter
Popis výsledku anglicky
This article deals with the benefits of PVD coatings ((Al,Ti)N; (Al,Ti,Cr)N and nanocomposite coating nACo®) applied to HSS three edges end milling cutters (producer ZPS – Frezovaci nastroje, Zlin, CZ). The coatings were synthesized by a cathodic-arc deposition process (producer Liss, Roznov pod Radhostem, CZ). Machining was carried out on the vertical milling machine FB 32V with using process liquid. Set up cutting conditions were con-stant throughout the machining. The aim of this experiment was to compare coated and uncoated HSS end milling cutters and find out the benefits of three kinds of PVD coatings. The monitored parameters were force loading and flank wear. Piezoeletrical dynamometer Kistler 9257B was used for measuring force loading and workshop opti-cal microscope was used for measuring flank wear (criterion VB). The construction steel C45E (1.1191; CSN 41 2050) was used as workpiece material. Best results were achieved by tool with PVD coating (Al,Ti,Cr)N.
Klasifikace
Druh
J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2016
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Manufacturing TECHNOLOGY
ISSN
1213-2489
e-ISSN
—
Svazek periodika
2016
Číslo periodika v rámci svazku
3
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
7
Strana od-do
506-512
Kód UT WoS článku
—
EID výsledku v databázi Scopus
2-s2.0-84974555656