AUTOMATIC STRAIGHTENING OF HARDENED SHAFTS
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F17%3APU126002" target="_blank" >RIV/00216305:26210/17:PU126002 - isvavai.cz</a>
Výsledek na webu
<a href="http://www.mmscience.eu/content/file/archives/MM_Science_201782.pdf" target="_blank" >http://www.mmscience.eu/content/file/archives/MM_Science_201782.pdf</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.17973/MMSJ.2017_12_201782" target="_blank" >10.17973/MMSJ.2017_12_201782</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
AUTOMATIC STRAIGHTENING OF HARDENED SHAFTS
Popis výsledku v původním jazyce
The main purpose of this article is to present a new way of straightening hardened shafts. The straightening of regular shafts is usually not difficult, but the situation is very different in case of hardened shafts. The regular shafts are usually straightened by bending of the shaft in the opposite direction than the original deformation. Sadly, this approach cannot be applied on hardened shafts, because of the brittleness of highly hardened material. Mesing Ltd. in cooperation with Brno University of Technology are now trying to automate the process of straightening by changing the stress inside of the hardened material. This method uses controlled impacts of a ram on the surface of the shaft which has to absorb the energy of the ram. The impact causes a plastic deformation of the surface of the shaft and changes the inner stress. At the end of this article is the design of such measuring and straightening setup shown and described.
Název v anglickém jazyce
AUTOMATIC STRAIGHTENING OF HARDENED SHAFTS
Popis výsledku anglicky
The main purpose of this article is to present a new way of straightening hardened shafts. The straightening of regular shafts is usually not difficult, but the situation is very different in case of hardened shafts. The regular shafts are usually straightened by bending of the shaft in the opposite direction than the original deformation. Sadly, this approach cannot be applied on hardened shafts, because of the brittleness of highly hardened material. Mesing Ltd. in cooperation with Brno University of Technology are now trying to automate the process of straightening by changing the stress inside of the hardened material. This method uses controlled impacts of a ram on the surface of the shaft which has to absorb the energy of the ram. The impact causes a plastic deformation of the surface of the shaft and changes the inner stress. At the end of this article is the design of such measuring and straightening setup shown and described.
Klasifikace
Druh
J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2017
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
MM Science Journal
ISSN
1803-1269
e-ISSN
1805-0476
Svazek periodika
December
Číslo periodika v rámci svazku
5
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
5
Strana od-do
2035-2039
Kód UT WoS článku
—
EID výsledku v databázi Scopus
2-s2.0-85038076335