Effect of width of kerf on machining accuracy and subsurface layer after WEDM

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F18%3APU124259" target="_blank" >RIV/00216305:26210/18:PU124259 - isvavai.cz</a>

Výsledek na webu

<a href="https://link.springer.com/article/10.1007/s11665-018-3239-4" target="_blank" >https://link.springer.com/article/10.1007/s11665-018-3239-4</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/s11665-018-3239-4" target="_blank" >10.1007/s11665-018-3239-4</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Effect of width of kerf on machining accuracy and subsurface layer after WEDM

Popis výsledku v původním jazyce

Wire electrical discharge machining (WEDM) is an unconventional machining technology that applies physical principles tomaterial removal.Material is removed by a series of recurring current discharges between the workpiece and the tool-electrode, and a ´kerf´ is created between the wire and the material being machined. The width of the kerf is directly dependant not only on the diameter of the wire used, but also on the machine parameter settingsand, in particular, on the set of mechanical and physical properties of the material being machined. To ensure precise machining, it is important to have the width of the kerf as small as possible. The presented study deals with the evaluation of the width of the kerf for 4 different metallic materials (some of them were subsequently heat treated using several methods) with different machine parameter settings. The kerf is investigated on metallographic cross sectionsusing light and electron microscopy.

Název v anglickém jazyce

Effect of width of kerf on machining accuracy and subsurface layer after WEDM

Popis výsledku anglicky

Wire electrical discharge machining (WEDM) is an unconventional machining technology that applies physical principles tomaterial removal.Material is removed by a series of recurring current discharges between the workpiece and the tool-electrode, and a ´kerf´ is created between the wire and the material being machined. The width of the kerf is directly dependant not only on the diameter of the wire used, but also on the machine parameter settingsand, in particular, on the set of mechanical and physical properties of the material being machined. To ensure precise machining, it is important to have the width of the kerf as small as possible. The presented study deals with the evaluation of the width of the kerf for 4 different metallic materials (some of them were subsequently heat treated using several methods) with different machine parameter settings. The kerf is investigated on metallographic cross sectionsusing light and electron microscopy.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2018

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Journal of Materials Engineering and Performance

ISSN

1059-9495

e-ISSN

1544-1024

Svazek periodika

27

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

US - Spojené státy americké

Počet stran výsledku

9

Strana od-do

1908-1916

Kód UT WoS článku

000429000000042

EID výsledku v databázi Scopus

2-s2.0-85044832423