Using a Design of Experiment for a Comprehensive Analysis of the Surface Quality and Cutting Speed in WED-Machined Hadfield Steel

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F19%3APU129002" target="_blank" >RIV/00216305:26210/19:PU129002 - isvavai.cz</a>

Výsledek na webu

<a href="https://link.springer.com/article/10.1007/s12206-019-0437-4?wt_mc=Internal.Event.1.SEM.ArticleAuthorOnlineFirst&utm_source=ArticleAuthorOnlineFirst&utm_medium=email&utm_content=AA_en_06082018&ArticleAuthorOnlineFirst_20190504" target="_blank" >https://link.springer.com/article/10.1007/s12206-019-0437-4?wt_mc=Internal.Event.1.SEM.ArticleAuthorOnlineFirst&utm_source=ArticleAuthorOnlineFirst&utm_medium=email&utm_content=AA_en_06082018&ArticleAuthorOnlineFirst_20190504</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/s12206-019-0437-4" target="_blank" >10.1007/s12206-019-0437-4</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Using a Design of Experiment for a Comprehensive Analysis of the Surface Quality and Cutting Speed in WED-Machined Hadfield Steel

Popis výsledku v původním jazyce

Wire Electrical Discharge Machining (WEDM) is an unconventional machining method used to manufacture complex-shaped, precise components. Considering the high-energy intensity of the wire erosion process, its effective implementation requires a maximum cutting speed while still ensuring the best possible quality of the machined surface. For this latter purpose, we conducted a design of experiment (DoE) comprising 33 cycles and five input factors, or machine setting parameters: gap voltage, pulse on time, pulse off time, discharge current, and wire feed. In this context, the present paper statistically evaluates the cutting speed in Hadfield steel, as related to machine setting parameters, and it also analyzes the machined surfaces of the applied samples. The actual experiment involved examining in detail the topography of the surfaces, using one contact and three non-contact profilers. The surface morphologies were observed via electron microscopy, and a lamella was prepared to facilitate the chemical composition analysis (EDX) with a transmission electron microscope (TEM). To study the subsurface layer and its defects, we produced metallographic specimens of all the samples; the observation of the items was performed by means of light and electron microscopes. With a maximum cutting speed the highest quality of the machined surface was achieved; however, the burned cavities can affect the life expectancy of the machined parts. The TEM lamella revealed that the individual alloying elements had segregated into regions, exhibiting high volumes of both manganese and the recast layer and, due to the use of WEDM, a manganese separation layer had formed at the boundary of the recast layer and the base material.

Název v anglickém jazyce

Using a Design of Experiment for a Comprehensive Analysis of the Surface Quality and Cutting Speed in WED-Machined Hadfield Steel

Popis výsledku anglicky

Wire Electrical Discharge Machining (WEDM) is an unconventional machining method used to manufacture complex-shaped, precise components. Considering the high-energy intensity of the wire erosion process, its effective implementation requires a maximum cutting speed while still ensuring the best possible quality of the machined surface. For this latter purpose, we conducted a design of experiment (DoE) comprising 33 cycles and five input factors, or machine setting parameters: gap voltage, pulse on time, pulse off time, discharge current, and wire feed. In this context, the present paper statistically evaluates the cutting speed in Hadfield steel, as related to machine setting parameters, and it also analyzes the machined surfaces of the applied samples. The actual experiment involved examining in detail the topography of the surfaces, using one contact and three non-contact profilers. The surface morphologies were observed via electron microscopy, and a lamella was prepared to facilitate the chemical composition analysis (EDX) with a transmission electron microscope (TEM). To study the subsurface layer and its defects, we produced metallographic specimens of all the samples; the observation of the items was performed by means of light and electron microscopes. With a maximum cutting speed the highest quality of the machined surface was achieved; however, the burned cavities can affect the life expectancy of the machined parts. The TEM lamella revealed that the individual alloying elements had segregated into regions, exhibiting high volumes of both manganese and the recast layer and, due to the use of WEDM, a manganese separation layer had formed at the boundary of the recast layer and the base material.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Journal of Mechanical Science and Technology

ISSN

1738-494X

e-ISSN

1976-3824

Svazek periodika

33

Číslo periodika v rámci svazku

5

Stát vydavatele periodika

KR - Korejská republika

Počet stran výsledku

16

Strana od-do

2371-2386

Kód UT WoS článku

000467438100040

EID výsledku v databázi Scopus

2-s2.0-85065673815