5-Axis Dry Milling of Bottom of Pocket by Ball and Circle-Segment End Mills

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F20%3APU136579" target="_blank" >RIV/00216305:26210/20:PU136579 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mmscience.eu/journal/issues/March%202020/articles/5-axis-dry-milling-of-bottom-of-pocket-by-ball-and-circle-segment-end-mills" target="_blank" >https://www.mmscience.eu/journal/issues/March%202020/articles/5-axis-dry-milling-of-bottom-of-pocket-by-ball-and-circle-segment-end-mills</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.17973/MMSJ.2020_03_2019153" target="_blank" >10.17973/MMSJ.2020_03_2019153</a>

Jazyk výsledku

angličtina

Název v původním jazyce

5-Axis Dry Milling of Bottom of Pocket by Ball and Circle-Segment End Mills

Popis výsledku v původním jazyce

At present, 5-axis machining is often realized with ball end mills that do not achieve the advantages of modern circle - segment end mills. However, to exploit the potential of these modern tools, it is necessary to use a special CAM software, including hyperMILL from Westcam. This software, increasing the efficiency of machining, was used in the present study, which compared these tools with respect to the quality of the machined surface, machining time and cutting forces. The workpiece material was aluminum alloy EN AW 7075-T6. At given cutting parameters, the circle-segment end mills achieved a lower Ra value and generally higher machining efficiency. At the end of the study, an assessment was made with respect to the economy.

Název v anglickém jazyce

5-Axis Dry Milling of Bottom of Pocket by Ball and Circle-Segment End Mills

Popis výsledku anglicky

At present, 5-axis machining is often realized with ball end mills that do not achieve the advantages of modern circle - segment end mills. However, to exploit the potential of these modern tools, it is necessary to use a special CAM software, including hyperMILL from Westcam. This software, increasing the efficiency of machining, was used in the present study, which compared these tools with respect to the quality of the machined surface, machining time and cutting forces. The workpiece material was aluminum alloy EN AW 7075-T6. At given cutting parameters, the circle-segment end mills achieved a lower Ra value and generally higher machining efficiency. At the end of the study, an assessment was made with respect to the economy.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2020

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

MM Science Journal

ISSN

1803-1269

e-ISSN

1805-0476

Svazek periodika

2020

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

5

Strana od-do

3740-3744

Kód UT WoS článku

000532576800007

EID výsledku v databázi Scopus

2-s2.0-85081040953