Importance of Melt Flow Direction during Injection Molding on Polymer Heat Sinks’ Cooling Efficiency

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F21%3APU140609" target="_blank" >RIV/00216305:26210/21:PU140609 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mdpi.com/2073-4360/13/8/1186" target="_blank" >https://www.mdpi.com/2073-4360/13/8/1186</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/polym13081186" target="_blank" >10.3390/polym13081186</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Importance of Melt Flow Direction during Injection Molding on Polymer Heat Sinks’ Cooling Efficiency

Popis výsledku v původním jazyce

Polymers with highly conductive fillers could possibly replace standardly used materials, such as aluminum and copper alloys, for passive cooling purposes. The main problem of the composite polymer-based heat sinks is that their high thermal conductivity is uneven. The orientation of this anisotropy is set according to the position of the highly thermally conductive filler. Its orientation is influenced by the melt flow during the polymer heat sink molding process. This article shows that change of the melt flow inside the mold cavity can improve the overall cooling efficiency of a polymer heat sink, which leads to lower temperatures on the heat source used. Two polymer heat sinks of identical geometries were produced. Their high thermal conductivity was given by the use of graphite flakes as the filler. The only difference between the heat sinks was in the position of the fan gate during their production. Different temperatures of the heat source between the two heat sinks were observed for the same measurement conditions. The measurements were conducted at Heatlab, BUT.

Název v anglickém jazyce

Importance of Melt Flow Direction during Injection Molding on Polymer Heat Sinks’ Cooling Efficiency

Popis výsledku anglicky

Polymers with highly conductive fillers could possibly replace standardly used materials, such as aluminum and copper alloys, for passive cooling purposes. The main problem of the composite polymer-based heat sinks is that their high thermal conductivity is uneven. The orientation of this anisotropy is set according to the position of the highly thermally conductive filler. Its orientation is influenced by the melt flow during the polymer heat sink molding process. This article shows that change of the melt flow inside the mold cavity can improve the overall cooling efficiency of a polymer heat sink, which leads to lower temperatures on the heat source used. Two polymer heat sinks of identical geometries were produced. Their high thermal conductivity was given by the use of graphite flakes as the filler. The only difference between the heat sinks was in the position of the fan gate during their production. Different temperatures of the heat source between the two heat sinks were observed for the same measurement conditions. The measurements were conducted at Heatlab, BUT.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20505 - Composites (including laminates, reinforced plastics, cermets, combined natural and synthetic fibre fabrics; filled composites)

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2021

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Polymers

ISSN

2073-4360

e-ISSN

—

Svazek periodika

13

Číslo periodika v rámci svazku

8

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

13

Strana od-do

1-13

Kód UT WoS článku

000644585700001

EID výsledku v databázi Scopus

2-s2.0-85104174247