Novel Approaches to the Design of an Ultra-Fast Magnetorheological Valve for Semi-Active Control

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F21%3APU140816" target="_blank" >RIV/00216305:26210/21:PU140816 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.mdpi.com/1996-1944/14/10/2500" target="_blank" >https://www.mdpi.com/1996-1944/14/10/2500</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.3390/ma14102500" target="_blank" >10.3390/ma14102500</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Novel Approaches to the Design of an Ultra-Fast Magnetorheological Valve for Semi-Active Control

Popis výsledku v původním jazyce

This article presents a list of suitable techniques and materials leading to the design of an ultra-fast magnetorheological (MR) valve. Two approaches for achieving the short response time are proposed: (a) by means of material, and (b) by means of the shape. Within the shape approach, the revolutionary technique of 3D metal printing using a selective laser melting (SLM) method was tested. The suitability of the materials and techniques is addressed based on the length of the response time, which is determined by the FEM. The simulation results determine the response time of the magnetic flux density on the step signal of the current. Subsequently, the response time is verified by the measurement of the simple magnetorheological valve. The following materials were tested: martensitic stainless steel AISI 420A (X20Cr13), cutting steel 11SMn30, pure iron for SLM, Sintex SMC STX prototyping material, ferrite N87, and Vacoflux 50. A special technique involving grooves was used for preventing eddy currents on materials with a high electrical conductivity. The simulation and experimental results indicate that a response time shorter than 2.5 ms can be achieved using materials such as Sintex SMC prototyping, ferrite N87, and grooved variants of metal pistons.

Název v anglickém jazyce

Novel Approaches to the Design of an Ultra-Fast Magnetorheological Valve for Semi-Active Control

Popis výsledku anglicky

This article presents a list of suitable techniques and materials leading to the design of an ultra-fast magnetorheological (MR) valve. Two approaches for achieving the short response time are proposed: (a) by means of material, and (b) by means of the shape. Within the shape approach, the revolutionary technique of 3D metal printing using a selective laser melting (SLM) method was tested. The suitability of the materials and techniques is addressed based on the length of the response time, which is determined by the FEM. The simulation results determine the response time of the magnetic flux density on the step signal of the current. Subsequently, the response time is verified by the measurement of the simple magnetorheological valve. The following materials were tested: martensitic stainless steel AISI 420A (X20Cr13), cutting steel 11SMn30, pure iron for SLM, Sintex SMC STX prototyping material, ferrite N87, and Vacoflux 50. A special technique involving grooves was used for preventing eddy currents on materials with a high electrical conductivity. The simulation and experimental results indicate that a response time shorter than 2.5 ms can be achieved using materials such as Sintex SMC prototyping, ferrite N87, and grooved variants of metal pistons.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/GJ20-23261Y" target="_blank" >GJ20-23261Y: Studium časové odezvy magnetoreologické kapaliny</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2021

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Materials

ISSN

1996-1944

e-ISSN

—

Svazek periodika

14

Číslo periodika v rámci svazku

10

Stát vydavatele periodika

CH - Švýcarská konfederace

Počet stran výsledku

20

Strana od-do

1-20

Kód UT WoS článku

000662525200001

EID výsledku v databázi Scopus

2-s2.0-85106602787