Effect of Holes in Overlap on the Load Capacity of the Single-Lap Adhesive Joints Made of EN AW-2024-T3 Aluminium Alloy
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F21%3APU143114" target="_blank" >RIV/00216305:26210/21:PU143114 - isvavai.cz</a>
Výsledek na webu
<a href="https://www.webofscience.com/wos/woscc/full-record/WOS:000739943500009" target="_blank" >https://www.webofscience.com/wos/woscc/full-record/WOS:000739943500009</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.2478/adms-2021-0029" target="_blank" >10.2478/adms-2021-0029</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Effect of Holes in Overlap on the Load Capacity of the Single-Lap Adhesive Joints Made of EN AW-2024-T3 Aluminium Alloy
Popis výsledku v původním jazyce
The paper presents the results of experimental research aimed at determining the possibilities of strengthening structural adhesive joints. Techniques to improve the strength of adhesive joints was to make holes in the front part of the adherends in order to make the joint locally more flexible in the area of stress concentration at the joint edges. The tests were carried out for the lap joints of EN AW-2024-T3 aluminum alloy sheets, which were bonded with Loctite EA3430 epoxy adhesive. Static tests were carried out on the basis of the tensile/shear test. It has been shown that the applied structural modifications allow for an increase in the strength of the joint, in the best variant, an increase in strength of 14.5% was obtained. In addition, it has been shown that making holes in the adherends allows to reduce the spread of strength results.
Název v anglickém jazyce
Effect of Holes in Overlap on the Load Capacity of the Single-Lap Adhesive Joints Made of EN AW-2024-T3 Aluminium Alloy
Popis výsledku anglicky
The paper presents the results of experimental research aimed at determining the possibilities of strengthening structural adhesive joints. Techniques to improve the strength of adhesive joints was to make holes in the front part of the adherends in order to make the joint locally more flexible in the area of stress concentration at the joint edges. The tests were carried out for the lap joints of EN AW-2024-T3 aluminum alloy sheets, which were bonded with Loctite EA3430 epoxy adhesive. Static tests were carried out on the basis of the tensile/shear test. It has been shown that the applied structural modifications allow for an increase in the strength of the joint, in the best variant, an increase in strength of 14.5% was obtained. In addition, it has been shown that making holes in the adherends allows to reduce the spread of strength results.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20501 - Materials engineering
Návaznosti výsledku
Projekt
—
Návaznosti
I - Institucionalni podpora na dlouhodoby koncepcni rozvoj vyzkumne organizace
Ostatní
Rok uplatnění
2021
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Advances in Materials Science
ISSN
2083-4799
e-ISSN
—
Svazek periodika
21
Číslo periodika v rámci svazku
4
Stát vydavatele periodika
PL - Polská republika
Počet stran výsledku
10
Strana od-do
112-121
Kód UT WoS článku
000739943500009
EID výsledku v databázi Scopus
—