Novel In-Situ Observation of the Grease Constituents in Elastohydrodynamic Contacts by Fluorescence Microscopy
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F22%3APU146146" target="_blank" >RIV/00216305:26210/22:PU146146 - isvavai.cz</a>
Výsledek na webu
<a href="https://doi.org/10.1007/s11249-022-01671-7" target="_blank" >https://doi.org/10.1007/s11249-022-01671-7</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1007/s11249-022-01671-7" target="_blank" >10.1007/s11249-022-01671-7</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Novel In-Situ Observation of the Grease Constituents in Elastohydrodynamic Contacts by Fluorescence Microscopy
Popis výsledku v původním jazyce
Grease is important lubricant for ball bearings as it is used much more often than oil. However, mechanism of the lubrication is not completely clear, especially concerning the role of the thickener in the lubricating process. It was shown that contribution of the thickener to film thickness build-up varies with operating conditions. Also, its influence on the resistive torque of the bearing was proved. However, all studies were in-direct showing its effects. This paper presents new in-situ fluorescence method of the grease constituents’ observation, where both, thickener, and base oil can be observed independently. Two different fluorescence dyes are used to distinguish grease constituents with the use of different microscope setup. Moreover, the new method was tested on two different test rigs. First is typical ball on disc test rig widely used for study of elastohydrodynamic lubrication. Second is ball on ring test rig which more closely represents radial ball bearing conditions. It was shown that thickener engagement is very different for each geometrical configuration.
Název v anglickém jazyce
Novel In-Situ Observation of the Grease Constituents in Elastohydrodynamic Contacts by Fluorescence Microscopy
Popis výsledku anglicky
Grease is important lubricant for ball bearings as it is used much more often than oil. However, mechanism of the lubrication is not completely clear, especially concerning the role of the thickener in the lubricating process. It was shown that contribution of the thickener to film thickness build-up varies with operating conditions. Also, its influence on the resistive torque of the bearing was proved. However, all studies were in-direct showing its effects. This paper presents new in-situ fluorescence method of the grease constituents’ observation, where both, thickener, and base oil can be observed independently. Two different fluorescence dyes are used to distinguish grease constituents with the use of different microscope setup. Moreover, the new method was tested on two different test rigs. First is typical ball on disc test rig widely used for study of elastohydrodynamic lubrication. Second is ball on ring test rig which more closely represents radial ball bearing conditions. It was shown that thickener engagement is very different for each geometrical configuration.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2022
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Tribology Letters
ISSN
1023-8883
e-ISSN
1573-2711
Svazek periodika
70
Číslo periodika v rámci svazku
126
Stát vydavatele periodika
US - Spojené státy americké
Počet stran výsledku
15
Strana od-do
1-15
Kód UT WoS článku
000879824600001
EID výsledku v databázi Scopus
2-s2.0-85141395301