Analysis of the machinability of different types of sintered carbides with WEDM in both water and oil bath

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F23%3APU147018" target="_blank" >RIV/00216305:26210/23:PU147018 - isvavai.cz</a>

Výsledek na webu

<a href="https://link.springer.com/article/10.1007/s00170-023-10913-4" target="_blank" >https://link.springer.com/article/10.1007/s00170-023-10913-4</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1007/s00170-023-10913-4" target="_blank" >10.1007/s00170-023-10913-4</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Analysis of the machinability of different types of sintered carbides with WEDM in both water and oil bath

Popis výsledku v původním jazyce

The unconventional Wire Electric Discharge Machining (WEDM) technology represents a vital manufacturing technology in different industrial branches. This technology is essential because of the possibility to machine difficult-to-machine materials such as sintered carbides. For this reason, this study analyses the machinability of sintered carbides WKP23S, WSM33S a WK1 with WEDM in both water and oil baths. We investigated the influence of the machining parameters, namely, pulse off time, gap voltage, discharge current, pulse on time, and wire feed, on the cutting speed, surface roughness, and defect occurrence. We investigated 9 different roughness parameters, analysed surface morphology with an electron microscope, and also analysed cross-sectioned samples. We found out that machining sintered carbides in oil bath yields better results than machining in deionized water. The oil tank prevents the removal of the cobalt binder, but it does not reduce fissure occurrence in any significant way. The lowest Ra value, that is 0.7 µm was recorded for the WKP23S sample when machined in oil and Ra 0.9 µm when the same material was machined in water.

Název v anglickém jazyce

Analysis of the machinability of different types of sintered carbides with WEDM in both water and oil bath

Popis výsledku anglicky

The unconventional Wire Electric Discharge Machining (WEDM) technology represents a vital manufacturing technology in different industrial branches. This technology is essential because of the possibility to machine difficult-to-machine materials such as sintered carbides. For this reason, this study analyses the machinability of sintered carbides WKP23S, WSM33S a WK1 with WEDM in both water and oil baths. We investigated the influence of the machining parameters, namely, pulse off time, gap voltage, discharge current, pulse on time, and wire feed, on the cutting speed, surface roughness, and defect occurrence. We investigated 9 different roughness parameters, analysed surface morphology with an electron microscope, and also analysed cross-sectioned samples. We found out that machining sintered carbides in oil bath yields better results than machining in deionized water. The oil tank prevents the removal of the cobalt binder, but it does not reduce fissure occurrence in any significant way. The lowest Ra value, that is 0.7 µm was recorded for the WKP23S sample when machined in oil and Ra 0.9 µm when the same material was machined in water.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

—

Rok uplatnění

2023

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

International Journal of Advanced Manufacturing Technology

ISSN

0268-3768

e-ISSN

1433-3015

Svazek periodika

124

Číslo periodika v rámci svazku

10

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

11

Strana od-do

„“-„“

Kód UT WoS článku

000920607700002

EID výsledku v databázi Scopus

2-s2.0-85146880318