Adaptation of conical liquid sheet and spray morphologies to cross-flowing gas

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F24%3APU147173" target="_blank" >RIV/00216305:26210/24:PU147173 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.sciencedirect.com/science/article/pii/S0301932223003348?via%3Dihub" target="_blank" >https://www.sciencedirect.com/science/article/pii/S0301932223003348?via%3Dihub</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1016/j.ijmultiphaseflow.2023.104714" target="_blank" >10.1016/j.ijmultiphaseflow.2023.104714</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Adaptation of conical liquid sheet and spray morphologies to cross-flowing gas

Popis výsledku v původním jazyce

A variety of industrial devices use liquid injection into the traverse stream of air. Ambient flow changes the spray characteristics, which can alter a system's function. Two different spill-return pressure-swirl atomizers (SRA) were investigated under cross -flow. One of the tested atomizers generates a conical liquid sheet with shorter breakup lengths due to reduced internal air-core stability. Phase Doppler anemometer (PDA) was used for 2D velocity and droplet size measurements, along with high-speed visualization to record instantaneous spray behaviour. A wide range of operating parameters was tested, e.g., inlet pressure (pl) ranging from 0.25 MPa to 1 MPa, spill-to-feed ratio (SFR) from 0 to 0.9, and cross -flow velocity from 0 to 32 m/s. As the cross -flow velocity increases, the spray starts to tilt and the breakup length (lb) shortens as a result of increased aerodynamic forces. This reduces the differences between atomizers. Moreover, the droplet diameter depends on the lb, yet no semiempirical model was found to accurately predict the droplet sizes. A map of breakup modes was established, and a transition point from long- to short-wave mode was identified. The Linear Stability Analysis of the liquid sheet breakup was used and compared with a semi-empirical approach for the first time for the SRA and cross -flow conditions. The results imply that considering only quiescent ambient conditions during atomizer development might not lead to the optimal design.

Název v anglickém jazyce

Adaptation of conical liquid sheet and spray morphologies to cross-flowing gas

Popis výsledku anglicky

A variety of industrial devices use liquid injection into the traverse stream of air. Ambient flow changes the spray characteristics, which can alter a system's function. Two different spill-return pressure-swirl atomizers (SRA) were investigated under cross -flow. One of the tested atomizers generates a conical liquid sheet with shorter breakup lengths due to reduced internal air-core stability. Phase Doppler anemometer (PDA) was used for 2D velocity and droplet size measurements, along with high-speed visualization to record instantaneous spray behaviour. A wide range of operating parameters was tested, e.g., inlet pressure (pl) ranging from 0.25 MPa to 1 MPa, spill-to-feed ratio (SFR) from 0 to 0.9, and cross -flow velocity from 0 to 32 m/s. As the cross -flow velocity increases, the spray starts to tilt and the breakup length (lb) shortens as a result of increased aerodynamic forces. This reduces the differences between atomizers. Moreover, the droplet diameter depends on the lb, yet no semiempirical model was found to accurately predict the droplet sizes. A map of breakup modes was established, and a transition point from long- to short-wave mode was identified. The Linear Stability Analysis of the liquid sheet breakup was used and compared with a semi-empirical approach for the first time for the SRA and cross -flow conditions. The results imply that considering only quiescent ambient conditions during atomizer development might not lead to the optimal design.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20300 - Mechanical engineering

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2024

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

INTERNATIONAL JOURNAL OF MULTIPHASE FLOW

ISSN

0301-9322

e-ISSN

1879-3533

Svazek periodika

172

Číslo periodika v rámci svazku

february 2024

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

12

Strana od-do

„“-„“

Kód UT WoS článku

001163473900001

EID výsledku v databázi Scopus

2-s2.0-85182265803