Experimental set-up for the validation of phase change models in case of direct and inverse heat transfer problems

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26210%2F24%3APU155268" target="_blank" >RIV/00216305:26210/24:PU155268 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.epj-conferences.org/articles/epjconf/pdf/2024/09/epjconf_efm2024_01040.pdf" target="_blank" >https://www.epj-conferences.org/articles/epjconf/pdf/2024/09/epjconf_efm2024_01040.pdf</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1051/epjconf/202429901040" target="_blank" >10.1051/epjconf/202429901040</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Experimental set-up for the validation of phase change models in case of direct and inverse heat transfer problems

Popis výsledku v původním jazyce

A number of models and modelling approaches for phase transitions of phase change materials (PCMs) have been proposed in recent years. However, many of these models have not been thoroughly validated with experimental data. This is in particular the case of the models for thermal hysteresis and partial phase transitions of PCMs, where the design and execution of relevant experiments is difficult. The most widely used experimental techniques for characterization of PCMs - Differential Scanning Calorimetry (DSC) and T-history method - require minimization of the temperature gradients in the test samples and thus the obtained results do not represent very well the behavior of PCMs in thermal energy storage (TES) systems (where large temperature gradients in PCMs are commonplace). An experimental set-up for the acquisition of data suitable for validation of phase change models have been proposed and assembled. The set-up can be used for the model validation in case of both the direct and inverse heat transfer problems. The set-up is based on the monitoring of the phase change front propagation in a rectangular cavity, where the positive or negative heat flux is introduced at one of the cavity walls. Such an arrangement results in (often significant) temperature gradients in a PCM. Unlike in similar experimental set-ups, where a heat transfer fluid (HTF) is used to introduce the heat flux at the wall, the Peltier cells are used in the proposed experimental set-up for this purpose. Also, most experiments reported in the literature only addressed the melting process (heating of a PCM) with the positive heat flux introduced at the wall. The Peltier cells allow for relatively quick switching between the positive and negative heat flux (heating/cooling) and as a result the thermal processes similar to real-life operation of TES systems can be investigated. The cubical cavity with 250 mm long internal edges is made of PMMA. The wall, at which the heat flux is introduced, is ma

Název v anglickém jazyce

Experimental set-up for the validation of phase change models in case of direct and inverse heat transfer problems

Popis výsledku anglicky

A number of models and modelling approaches for phase transitions of phase change materials (PCMs) have been proposed in recent years. However, many of these models have not been thoroughly validated with experimental data. This is in particular the case of the models for thermal hysteresis and partial phase transitions of PCMs, where the design and execution of relevant experiments is difficult. The most widely used experimental techniques for characterization of PCMs - Differential Scanning Calorimetry (DSC) and T-history method - require minimization of the temperature gradients in the test samples and thus the obtained results do not represent very well the behavior of PCMs in thermal energy storage (TES) systems (where large temperature gradients in PCMs are commonplace). An experimental set-up for the acquisition of data suitable for validation of phase change models have been proposed and assembled. The set-up can be used for the model validation in case of both the direct and inverse heat transfer problems. The set-up is based on the monitoring of the phase change front propagation in a rectangular cavity, where the positive or negative heat flux is introduced at one of the cavity walls. Such an arrangement results in (often significant) temperature gradients in a PCM. Unlike in similar experimental set-ups, where a heat transfer fluid (HTF) is used to introduce the heat flux at the wall, the Peltier cells are used in the proposed experimental set-up for this purpose. Also, most experiments reported in the literature only addressed the melting process (heating of a PCM) with the positive heat flux introduced at the wall. The Peltier cells allow for relatively quick switching between the positive and negative heat flux (heating/cooling) and as a result the thermal processes similar to real-life operation of TES systems can be investigated. The cubical cavity with 250 mm long internal edges is made of PMMA. The wall, at which the heat flux is introduced, is ma

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20303 - Thermodynamics

Projekt

<a href="/cs/project/GA22-31173S" target="_blank" >GA22-31173S: Adaptivní soft computing framework pro řešení inverzních úloh přenosu tepla se změnou skupenství</a><br>

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2024

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

16th International Conference on Experimental Fluid Mechanics, EFM 2022

ISBN

—

ISSN

2101-6275

e-ISSN

—

Počet stran výsledku

5

Strana od-do

„01040“-„“

Název nakladatele

EDP Sciences

Místo vydání

neuveden

Místo konání akce

Dvůr Králové nad Labem

Datum konání akce

29. 11. 2022

Typ akce podle státní příslušnosti

EUR - Evropská akce

Kód UT WoS článku

—