Characterization of porosity and hollow defects in ceramic objects built by extrusion additive manufacturing

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26620%2F21%3APU141809" target="_blank" >RIV/00216305:26620/21:PU141809 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.webofscience.com/wos/woscc/full-record/WOS:000701887600001" target="_blank" >https://www.webofscience.com/wos/woscc/full-record/WOS:000701887600001</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1016/j.addma.2021.102272" target="_blank" >10.1016/j.addma.2021.102272</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Characterization of porosity and hollow defects in ceramic objects built by extrusion additive manufacturing

Popis výsledku v původním jazyce

Direct ink writing, or robocasting, is an extrusion additive manufacturing technique for the fabrication of complex ceramic parts. Pores are common defects in post-sintered robocast parts that strongly influence the performance by changing the density, the transport properties, and the mechanical strength. In this work, the porosity (volumetric fraction, size distribution, geometry and topological distribution) of monolithic and 3D-lattice specimens made of hydroxyapatite was comprehensively characterized at multiple length scales through the six most widely used experimental methods for the study of porous materials. These two types of samples embrace the two most common types of additive manufactured ceramics and allowed the study of materials with pores in the submicron scale, as well as materials with a bimodal pore size distribution at significantly different length scales. Detected pores were divided into (1) engineered porosity set by the structural design, and (2) hollow defects, including intergranular porosity, trapped-air pores, cracks, and cavities, that overlapped at different length scales with the engineered porosity. The origin and mechanisms of formation of hollow defects are discussed, providing guidelines to avoid them. The experimental methods that allow discerning between pores and hollow defects are highlighted, and their advantages and drawbacks are discussed. This work might serve as a guide for the selection of the proper combination of methods for the pore evaluation of similar additive manufactured parts.

Název v anglickém jazyce

Characterization of porosity and hollow defects in ceramic objects built by extrusion additive manufacturing

Popis výsledku anglicky

Direct ink writing, or robocasting, is an extrusion additive manufacturing technique for the fabrication of complex ceramic parts. Pores are common defects in post-sintered robocast parts that strongly influence the performance by changing the density, the transport properties, and the mechanical strength. In this work, the porosity (volumetric fraction, size distribution, geometry and topological distribution) of monolithic and 3D-lattice specimens made of hydroxyapatite was comprehensively characterized at multiple length scales through the six most widely used experimental methods for the study of porous materials. These two types of samples embrace the two most common types of additive manufactured ceramics and allowed the study of materials with pores in the submicron scale, as well as materials with a bimodal pore size distribution at significantly different length scales. Detected pores were divided into (1) engineered porosity set by the structural design, and (2) hollow defects, including intergranular porosity, trapped-air pores, cracks, and cavities, that overlapped at different length scales with the engineered porosity. The origin and mechanisms of formation of hollow defects are discussed, providing guidelines to avoid them. The experimental methods that allow discerning between pores and hollow defects are highlighted, and their advantages and drawbacks are discussed. This work might serve as a guide for the selection of the proper combination of methods for the pore evaluation of similar additive manufactured parts.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20504 - Ceramics

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2021

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Additive Manufacturing

ISSN

2214-8604

e-ISSN

—

Svazek periodika

47

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

NL - Nizozemsko

Počet stran výsledku

12

Strana od-do

1-12

Kód UT WoS článku

000701887600001

EID výsledku v databázi Scopus

2-s2.0-85114123813