Vše

Co hledáte?

Vše
Projekty
Výsledky výzkumu
Subjekty

Rychlé hledání

  • Projekty podpořené TA ČR
  • Významné projekty
  • Projekty s nejvyšší státní podporou
  • Aktuálně běžící projekty

Chytré vyhledávání

  • Takto najdu konkrétní +slovo
  • Takto z výsledků -slovo zcela vynechám
  • “Takto můžu najít celou frázi”

Effect of powder milling on sintering behavior and monotonic and cyclic mechanical properties of Mo and Mo-Si lattices produced by direct ink writing

Identifikátory výsledku

  • Kód výsledku v IS VaVaI

    <a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F00216305%3A26620%2F23%3APU150155" target="_blank" >RIV/00216305:26620/23:PU150155 - isvavai.cz</a>

  • Výsledek na webu

    <a href="https://www.sciencedirect.com/science/article/pii/S2238785423024511" target="_blank" >https://www.sciencedirect.com/science/article/pii/S2238785423024511</a>

  • DOI - Digital Object Identifier

    <a href="http://dx.doi.org/10.1016/j.jmrt.2023.10.002" target="_blank" >10.1016/j.jmrt.2023.10.002</a>

Alternativní jazyky

  • Jazyk výsledku

    angličtina

  • Název v původním jazyce

    Effect of powder milling on sintering behavior and monotonic and cyclic mechanical properties of Mo and Mo-Si lattices produced by direct ink writing

  • Popis výsledku v původním jazyce

    Molybdenum is a refractory metal regarded as a promising basis for producing high-temperature components. However, the potential of manufacturing molybdenum-based structures by direct ink writing (DIW) has not been explored. In this study, three-dimensional porous molybdenum (Mo) and molybdenum-silicon (Mo-Si) composite lattices were fabricated using DIW with non-milled and milled powders. The effects of Mo powder morphology (resulting from milling) and chemical composition (alloying Mo with 3 and 10 wt% of Si) on the microstructure, phase composition, and static and cyclic compression properties at room temperature were investigated. Lattices fabricated from commercial spherical Mo powder exhibited the highest intra-filament porosity. Conversely, lattices fabricated from milled Mo powder were denser and had higher compressive strength, offset stress, and quasi-elastic gradient. Alloying Mo with Si during sintering resulted in composite lattices with Mo thorn Mo3Si microstructure. A low content of Mo3Si slightly decreased monotonic compression properties but did not affect the cyclic compression response compared to Mo lattices made from milled powder. In contrast, a high content of Mo3Si produced quasi-brittle lattices with reduced compressive strength and increased damage accumulation during cyclic loading. The cyclic behavior of all lattices was characterized by a ratcheting-dominated stress-strain response. Lattices fabricated from milled Mo and milled Mo-3 wt.%Si powders demonstrated superior performance compared to those fabricated from commercial spherical Mo and milled Mo-10 wt%Si powders. The results suggest that using milled powders can enhance the mechanical reliability and promote the use of DIW as preferred additive manufacturing technology for the fabrication of Mo-Si composite lattices. (c) 2023 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

  • Název v anglickém jazyce

    Effect of powder milling on sintering behavior and monotonic and cyclic mechanical properties of Mo and Mo-Si lattices produced by direct ink writing

  • Popis výsledku anglicky

    Molybdenum is a refractory metal regarded as a promising basis for producing high-temperature components. However, the potential of manufacturing molybdenum-based structures by direct ink writing (DIW) has not been explored. In this study, three-dimensional porous molybdenum (Mo) and molybdenum-silicon (Mo-Si) composite lattices were fabricated using DIW with non-milled and milled powders. The effects of Mo powder morphology (resulting from milling) and chemical composition (alloying Mo with 3 and 10 wt% of Si) on the microstructure, phase composition, and static and cyclic compression properties at room temperature were investigated. Lattices fabricated from commercial spherical Mo powder exhibited the highest intra-filament porosity. Conversely, lattices fabricated from milled Mo powder were denser and had higher compressive strength, offset stress, and quasi-elastic gradient. Alloying Mo with Si during sintering resulted in composite lattices with Mo thorn Mo3Si microstructure. A low content of Mo3Si slightly decreased monotonic compression properties but did not affect the cyclic compression response compared to Mo lattices made from milled powder. In contrast, a high content of Mo3Si produced quasi-brittle lattices with reduced compressive strength and increased damage accumulation during cyclic loading. The cyclic behavior of all lattices was characterized by a ratcheting-dominated stress-strain response. Lattices fabricated from milled Mo and milled Mo-3 wt.%Si powders demonstrated superior performance compared to those fabricated from commercial spherical Mo and milled Mo-10 wt%Si powders. The results suggest that using milled powders can enhance the mechanical reliability and promote the use of DIW as preferred additive manufacturing technology for the fabrication of Mo-Si composite lattices. (c) 2023 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

Klasifikace

  • Druh

    J<sub>imp</sub> - Článek v periodiku v databázi Web of Science

  • CEP obor

  • OECD FORD obor

    20501 - Materials engineering

Návaznosti výsledku

  • Projekt

    <a href="/cs/project/LTC20068" target="_blank" >LTC20068: New materials for emerging energy technologies</a><br>

  • Návaznosti

    P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Ostatní

  • Rok uplatnění

    2023

  • Kód důvěrnosti údajů

    S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Údaje specifické pro druh výsledku

  • Název periodika

    Journal of Materials Research and Technology

  • ISSN

    2238-7854

  • e-ISSN

    2214-0697

  • Svazek periodika

    27

  • Číslo periodika v rámci svazku

    10

  • Stát vydavatele periodika

    BR - Brazilská federativní republika

  • Počet stran výsledku

    15

  • Strana od-do

    2475-2489

  • Kód UT WoS článku

    001105470800001

  • EID výsledku v databázi Scopus

    2-s2.0-85174149540