Vše

Co hledáte?

Vše
Projekty
Výsledky výzkumu
Subjekty

Rychlé hledání

  • Projekty podpořené TA ČR
  • Významné projekty
  • Projekty s nejvyšší státní podporou
  • Aktuálně běžící projekty

Chytré vyhledávání

  • Takto najdu konkrétní +slovo
  • Takto z výsledků -slovo zcela vynechám
  • “Takto můžu najít celou frázi”

The Use of Explosive Energy for Joining Advanced High Strength Low Alloy Steels

Identifikátory výsledku

  • Kód výsledku v IS VaVaI

    <a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F26316919%3A_____%2F13%3AN0000001" target="_blank" >RIV/26316919:_____/13:N0000001 - isvavai.cz</a>

  • Nalezeny alternativní kódy

    RIV/49777513:23210/13:43927941

  • Výsledek na webu

    <a href="http://link.springer.com/article/10.1007%2Fs11665-012-0210-7#/page-1" target="_blank" >http://link.springer.com/article/10.1007%2Fs11665-012-0210-7#/page-1</a>

  • DOI - Digital Object Identifier

    <a href="http://dx.doi.org/10.1007/s11665-012-0210-7" target="_blank" >10.1007/s11665-012-0210-7</a>

Alternativní jazyky

  • Jazyk výsledku

    angličtina

  • Název v původním jazyce

    The Use of Explosive Energy for Joining Advanced High Strength Low Alloy Steels

  • Popis výsledku v původním jazyce

    This article deals with an alternative method of joining advanced steels for frame structures. These steels cannot be joined by a conventional process due to the impact of temperature on the base material. Therefore, a simple and cost-effective method of forming a high-strength joint, intended for advanced highstrength materials, was designed using explosive forming. One of its key advantages is that it preserves the microstructure of the high-strength material being joined. At the same time, the design of the joint allows it to undergo further plastic deformation if the yield stress is exceeded, thus preventing the step change in load-carrying capacity and the instability of the structure. The alternative joint was intended for materials with yield stress above 1000 MPa and elongation of 10%, under quasi-static conditions. However, the design is also suitable for materials with ultimate tensile strength higher than 2000 MPa. Testing of the load-carrying capacity of the joint in a mechanical testing shop showed that the larger the flow stress of the material, the higher the load-carrying capacity of the joint. The selected joint designs with good loadbearing capacity values were manufactured by forming using products of detonation of the SEMTEX industrial blasting explosive. In a compression test, the demonstration joints showed the axial load-bearing capacity of 200 kN with up to 20-mm displacement to failure.

  • Název v anglickém jazyce

    The Use of Explosive Energy for Joining Advanced High Strength Low Alloy Steels

  • Popis výsledku anglicky

    This article deals with an alternative method of joining advanced steels for frame structures. These steels cannot be joined by a conventional process due to the impact of temperature on the base material. Therefore, a simple and cost-effective method of forming a high-strength joint, intended for advanced highstrength materials, was designed using explosive forming. One of its key advantages is that it preserves the microstructure of the high-strength material being joined. At the same time, the design of the joint allows it to undergo further plastic deformation if the yield stress is exceeded, thus preventing the step change in load-carrying capacity and the instability of the structure. The alternative joint was intended for materials with yield stress above 1000 MPa and elongation of 10%, under quasi-static conditions. However, the design is also suitable for materials with ultimate tensile strength higher than 2000 MPa. Testing of the load-carrying capacity of the joint in a mechanical testing shop showed that the larger the flow stress of the material, the higher the load-carrying capacity of the joint. The selected joint designs with good loadbearing capacity values were manufactured by forming using products of detonation of the SEMTEX industrial blasting explosive. In a compression test, the demonstration joints showed the axial load-bearing capacity of 200 kN with up to 20-mm displacement to failure.

Klasifikace

  • Druh

    J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

  • CEP obor

    JP - Průmyslové procesy a zpracování

  • OECD FORD obor

Návaznosti výsledku

  • Projekt

    <a href="/cs/project/1M06032" target="_blank" >1M06032: VÝZKUMNÉ CENTRUM TVÁŘECÍCH TECHNOLOGIÍ</a><br>

  • Návaznosti

    P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Ostatní

  • Rok uplatnění

    2013

  • Kód důvěrnosti údajů

    S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Údaje specifické pro druh výsledku

  • Název periodika

    Journal of Materials Engineering and Performance

  • ISSN

    1059-9495

  • e-ISSN

  • Svazek periodika

    22

  • Číslo periodika v rámci svazku

    3/2013

  • Stát vydavatele periodika

    US - Spojené státy americké

  • Počet stran výsledku

    5

  • Strana od-do

    748-752

  • Kód UT WoS článku

    000314899800013

  • EID výsledku v databázi Scopus