FEM Analyses of the Radiation in Heating Forging Furnace

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F26316919%3A_____%2F14%3A%230000556" target="_blank" >RIV/26316919:_____/14:#0000556 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.4028/www.scientific.net/AMM.751.235" target="_blank" >http://dx.doi.org/10.4028/www.scientific.net/AMM.751.235</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/AMM.751.235" target="_blank" >10.4028/www.scientific.net/AMM.751.235</a>

Jazyk výsledku

angličtina

Název v původním jazyce

FEM Analyses of the Radiation in Heating Forging Furnace

Popis výsledku v původním jazyce

The purpose of this study was to identify possible causes of longitudinal surface cracks found during early stages of ingot breakdown. However, these cracks need not necessarily form during forging or as a result of poor quality of the surface in metallurgical terms. Under certain conditions, they may occur even as the ingot is being heated in the furnace to the forging temperature. The cracks probably form within a few minutes after placing the ingot in the furnace as a result of the temperature gradient, which is most severe on the ingot surface. A numerical model was created to represent the case of three ingots in a furnace. Upon casting, the ingots are cooled down to no more than 600°C and then placed in a furnace at 1,100 - 1,200°C. Numerical simulations were used to analyse their internal stresses and temperatures.

Název v anglickém jazyce

FEM Analyses of the Radiation in Heating Forging Furnace

Popis výsledku anglicky

The purpose of this study was to identify possible causes of longitudinal surface cracks found during early stages of ingot breakdown. However, these cracks need not necessarily form during forging or as a result of poor quality of the surface in metallurgical terms. Under certain conditions, they may occur even as the ingot is being heated in the furnace to the forging temperature. The cracks probably form within a few minutes after placing the ingot in the furnace as a result of the temperature gradient, which is most severe on the ingot surface. A numerical model was created to represent the case of three ingots in a furnace. Upon casting, the ingots are cooled down to no more than 600°C and then placed in a furnace at 1,100 - 1,200°C. Numerical simulations were used to analyse their internal stresses and temperatures.

Druh

D - Stať ve sborníku

CEP obor

JG - Hutnictví, kovové materiály

OECD FORD obor

—

Projekt

<a href="/cs/project/ED2.1.00%2F03.0077" target="_blank" >ED2.1.00/03.0077: Západočeské materiálově metalurgické centrum</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2014

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Material Science, Applied Mechanics and Advanced Engineering Research

ISBN

978-3-03835-451-2

ISSN

1660-9336

e-ISSN

—

Počet stran výsledku

4

Strana od-do

235-238

Název nakladatele

Trans Tech Publication Ltd.

Místo vydání

Pfaffikon, Švýcarsko

Místo konání akce

Bangkok, Thajsko

Datum konání akce

9. 12. 2014

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—