Creep test with use of miniaturized specimens

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F26316919%3A_____%2F17%3AN0000035" target="_blank" >RIV/26316919:_____/17:N0000035 - isvavai.cz</a>

Výsledek na webu

<a href="http://iopscience.iop.org/1757-899X/179/1/012032" target="_blank" >http://iopscience.iop.org/1757-899X/179/1/012032</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1088/1757-899X/179/1/012032" target="_blank" >10.1088/1757-899X/179/1/012032</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Creep test with use of miniaturized specimens

Popis výsledku v původním jazyce

Application of the mini samples methods is very common especially for residual service life assessment of the components operating in the energy sector. Residual lifetime of operating device can be evaluated using standard tests, but these usually cannot be performed due to limited material amount that can be extracted from the components. It is possible to use in these cases a semi destructive sampling of materials and testing methods employing miniature specimens. This article deals with comparison of the creep results obtained with the use of on standard test bars and sub sized samples such as Small Punch Test and newly proposed miniature samples that are axially loaded. The experiment was performed on steam line steel CSN 15 128 after operation. Emphasis was put to practical use of the test results and therefore residual life was assessed with the use of standard and new mini specimens. The results obtained for standard and mini samples exhibit very good agreement without necessity of any correlation as in the case of SPT and thus much more straight forward approach can be applied even for "unknown materials".

Název v anglickém jazyce

Creep test with use of miniaturized specimens

Popis výsledku anglicky

Application of the mini samples methods is very common especially for residual service life assessment of the components operating in the energy sector. Residual lifetime of operating device can be evaluated using standard tests, but these usually cannot be performed due to limited material amount that can be extracted from the components. It is possible to use in these cases a semi destructive sampling of materials and testing methods employing miniature specimens. This article deals with comparison of the creep results obtained with the use of on standard test bars and sub sized samples such as Small Punch Test and newly proposed miniature samples that are axially loaded. The experiment was performed on steam line steel CSN 15 128 after operation. Emphasis was put to practical use of the test results and therefore residual life was assessed with the use of standard and new mini specimens. The results obtained for standard and mini samples exhibit very good agreement without necessity of any correlation as in the case of SPT and thus much more straight forward approach can be applied even for "unknown materials".

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20306 - Audio engineering, reliability analysis

Projekt

<a href="/cs/project/LO1412" target="_blank" >LO1412: Rozvoj Západočeského materiálově metalurgického Centra</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

4th International Conference Recent Trends in Structural Materials (COMAT 2016)

ISBN

—

ISSN

1757-8981

e-ISSN

—

Počet stran výsledku

6

Strana od-do

nestránkováno

Název nakladatele

IOP Publishing

Místo vydání

Bristol

Místo konání akce

Plzeň

Datum konání akce

9. 11. 2016

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

000403407100032