Induction Melting of Aluminium Oxide in the Cold Crucible

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F26722445%3A_____%2F17%3AN0000047" target="_blank" >RIV/26722445:_____/17:N0000047 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Induction Melting of Aluminium Oxide in the Cold Crucible

Popis výsledku v původním jazyce

This article deals with the process of the experimental induction melting of aluminium oxide in so called cold crucible (CC). The experiment took place in a couple of steps, that were needed for a successful realisation of the melting. The first step was the designing of suitable parameters of the cold crucible regarding the depth of penetration of the eddy currents into the melted aluminium oxide and the output power of the high frequency generator for melting in the cold crucible. The process of the experiment itself then consisted in the preparation of cold crucible for melting. The overheating of the starting material to the melting point of the load. The melting of the load. The endurance of the load in steady-state at a constant temperature. The controlled cooling of the load. The removal of the ingot of aluminium oxide from the cold crucible. The article is dedicated to the process of the experiment with respect to the development of the heating losses considering the input power during the melting process in the whole induction system.

Název v anglickém jazyce

Induction Melting of Aluminium Oxide in the Cold Crucible

Popis výsledku anglicky

This article deals with the process of the experimental induction melting of aluminium oxide in so called cold crucible (CC). The experiment took place in a couple of steps, that were needed for a successful realisation of the melting. The first step was the designing of suitable parameters of the cold crucible regarding the depth of penetration of the eddy currents into the melted aluminium oxide and the output power of the high frequency generator for melting in the cold crucible. The process of the experiment itself then consisted in the preparation of cold crucible for melting. The overheating of the starting material to the melting point of the load. The melting of the load. The endurance of the load in steady-state at a constant temperature. The controlled cooling of the load. The removal of the ingot of aluminium oxide from the cold crucible. The article is dedicated to the process of the experiment with respect to the development of the heating losses considering the input power during the melting process in the whole induction system.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20200 - Electrical engineering, Electronic engineering, Information engineering

Projekt

Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

PROCEEDINGS OF THE 2017 18TH INTERNATIONAL SCIENTIFIC CONFERENCE ON ELECTRIC POWER ENGINEERING (EPE)

ISBN

978-1-5090-6406-9

ISSN

2376-5623

e-ISSN

—

Počet stran výsledku

4

Strana od-do

707-710

Název nakladatele

IEEE

Místo vydání

New York, USA

Místo konání akce

Kouty nad Desnou

Datum konání akce

17. 5. 2017

Typ akce podle státní příslušnosti

EUR - Evropská akce

Kód UT WoS článku

000422921000131