Vše

Co hledáte?

Vše
Projekty
Výsledky výzkumu
Subjekty

Rychlé hledání

  • Projekty podpořené TA ČR
  • Významné projekty
  • Projekty s nejvyšší státní podporou
  • Aktuálně běžící projekty

Chytré vyhledávání

  • Takto najdu konkrétní +slovo
  • Takto z výsledků -slovo zcela vynechám
  • “Takto můžu najít celou frázi”

Measurement of hydraulic characteristics of different electrodialysis modules

Identifikátory výsledku

  • Kód výsledku v IS VaVaI

    <a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F28676092%3A_____%2F16%3AN0000053" target="_blank" >RIV/28676092:_____/16:N0000053 - isvavai.cz</a>

  • Výsledek na webu

  • DOI - Digital Object Identifier

Alternativní jazyky

  • Jazyk výsledku

    angličtina

  • Název v původním jazyce

    Measurement of hydraulic characteristics of different electrodialysis modules

  • Popis výsledku v původním jazyce

    The objective of this project was to measure hydraulic characteristics of various pilot electrodialysis modules and to analyze these data. There were assembled eight modules with different amount of membrane cells and different types of spacers. To measure their hydraulic characteristics, it was used a unit in which four experiments were accomplished using tap water: measurement of pressure drops between an inlet and an outlet flow, measurement of pressure difference between two different inlet flows, measurement of internal leakages and measurement of external leakages. Pressure drop was measured in the range of linear flow velocities 2.5 – 10.5 cm s-1. Pressure difference between two inlet flows was measured in order to check the correctness of module assembling as this difference should be as low as possible. When measuring internal leakages, only one module circuit was connected to water circulation (linear flow velocity 1 cm s-1) and the other circuits remained disconnected. The rate of internal leakages was set as the amount of water leaking from disconnected circuits per unit of time. External leakages from membrane stack were measured at three pressures – 1.5, 2.0 and 2.5 bar. The obtained results showed that both, number of membrane cells and type of spacers (material, net type, design of distribution channels) influenced hydraulic characteristics of the modules. Even some data were inconclusive, most of them are important in developing new electrodialysis modules for specific processes.

  • Název v anglickém jazyce

    Measurement of hydraulic characteristics of different electrodialysis modules

  • Popis výsledku anglicky

    The objective of this project was to measure hydraulic characteristics of various pilot electrodialysis modules and to analyze these data. There were assembled eight modules with different amount of membrane cells and different types of spacers. To measure their hydraulic characteristics, it was used a unit in which four experiments were accomplished using tap water: measurement of pressure drops between an inlet and an outlet flow, measurement of pressure difference between two different inlet flows, measurement of internal leakages and measurement of external leakages. Pressure drop was measured in the range of linear flow velocities 2.5 – 10.5 cm s-1. Pressure difference between two inlet flows was measured in order to check the correctness of module assembling as this difference should be as low as possible. When measuring internal leakages, only one module circuit was connected to water circulation (linear flow velocity 1 cm s-1) and the other circuits remained disconnected. The rate of internal leakages was set as the amount of water leaking from disconnected circuits per unit of time. External leakages from membrane stack were measured at three pressures – 1.5, 2.0 and 2.5 bar. The obtained results showed that both, number of membrane cells and type of spacers (material, net type, design of distribution channels) influenced hydraulic characteristics of the modules. Even some data were inconclusive, most of them are important in developing new electrodialysis modules for specific processes.

Klasifikace

  • Druh

    D - Stať ve sborníku

  • CEP obor

    JP - Průmyslové procesy a zpracování

  • OECD FORD obor

Návaznosti výsledku

  • Projekt

    <a href="/cs/project/LO1418" target="_blank" >LO1418: Progresivní rozvoj Membránového inovačního centra</a><br>

  • Návaznosti

    P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Ostatní

  • Rok uplatnění

    2016

  • Kód důvěrnosti údajů

    C - Předmět řešení projektu podléhá obchodnímu tajemství (§ 504 Občanského zákoníku), ale název projektu, cíle projektu a u ukončeného nebo zastaveného projektu zhodnocení výsledku řešení projektu (údaje P03, P04, P15, P19, P29, PN8) dodané do CEP, jsou upraveny tak, aby byly zveřejnitelné.

Údaje specifické pro druh výsledku

  • Název statě ve sborníku

    Workshop of Students’ Presentations 2016, Membranes and Membrane Processes

  • ISBN

    978-80-904517-8-0

  • ISSN

  • e-ISSN

  • Počet stran výsledku

    12

  • Strana od-do

  • Název nakladatele

    Czech Membrane Platform

  • Místo vydání

    Česká Lípa

  • Místo konání akce

    Straz pod Ralskem, Czech Republic

  • Datum konání akce

    12. 10. 2016

  • Typ akce podle státní příslušnosti

    WRD - Celosvětová akce

  • Kód UT WoS článku