New Ways at Fine Grinding

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F44555601%3A13420%2F14%3A43885579" target="_blank" >RIV/44555601:13420/14:43885579 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.4028/www.scientific.net/KEM.581.255" target="_blank" >http://dx.doi.org/10.4028/www.scientific.net/KEM.581.255</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.4028/www.scientific.net/KEM.581.255" target="_blank" >10.4028/www.scientific.net/KEM.581.255</a>

Jazyk výsledku

angličtina

Název v původním jazyce

New Ways at Fine Grinding

Popis výsledku v původním jazyce

The traditional approach to grinding is to operate within the limits of surface quality. The requirements for surface quality in grinding are higher than those in other common machining operations such as turning and milling. The surface quality of machined parts is very important for precise production and assembly. When we focus on roughness parameters after grinding, we can establish the limits of these parameters for typical grain materials: Al2O3, SiC, CBN, SG and others. Increasing demands on accuracy and quality of production leads to research concerned with the properties of these materials and the surface quality after grinding. This paper shows new possibilities for the ground surface with focus on surface roughness obtained under varying combinations of cutting conditions. The influence of the grinding wheel, cutting parameters and coolant on higher surface quality is assessed by roughness parameters Ra, Rz, Rt and the Material portion of a surface profile. These high-precis

Název v anglickém jazyce

New Ways at Fine Grinding

Popis výsledku anglicky

The traditional approach to grinding is to operate within the limits of surface quality. The requirements for surface quality in grinding are higher than those in other common machining operations such as turning and milling. The surface quality of machined parts is very important for precise production and assembly. When we focus on roughness parameters after grinding, we can establish the limits of these parameters for typical grain materials: Al2O3, SiC, CBN, SG and others. Increasing demands on accuracy and quality of production leads to research concerned with the properties of these materials and the surface quality after grinding. This paper shows new possibilities for the ground surface with focus on surface roughness obtained under varying combinations of cutting conditions. The influence of the grinding wheel, cutting parameters and coolant on higher surface quality is assessed by roughness parameters Ra, Rz, Rt and the Material portion of a surface profile. These high-precis

Druh

D - Stať ve sborníku

CEP obor

JR - Ostatní strojírenství

OECD FORD obor

—

Projekt

<a href="/cs/project/EE2.3.30.0028" target="_blank" >EE2.3.30.0028: Materiály a lidské zdroje pro životní prostředí</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2014

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Key Engineerings Materilas

ISBN

978-3-03785-840-0

ISSN

1013-9826

e-ISSN

—

Počet stran výsledku

6

Strana od-do

255-260

Název nakladatele

Trans Tech Publication Ltd.

Místo vydání

Zurich

Místo konání akce

Miskolc

Datum konání akce

3. 10. 2013

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—