Modification of AlSi9CuMnNi alloy by antimony and heat treatment and their influence on tool wear after turning

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F44555601%3A13420%2F16%3A43888018" target="_blank" >RIV/44555601:13420/16:43888018 - isvavai.cz</a>

Výsledek na webu

—

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Modification of AlSi9CuMnNi alloy by antimony and heat treatment and their influence on tool wear after turning

Popis výsledku v původním jazyce

Modification alloy is an important part of the metallurgical process, and this also applies, of course, for aluminum alloys, particularly for Al-Si (silumins). As a modification of the material we can use the modification using the selected element or heat treatment of alloys, or a combination of both processes. One of the elements that it is possible to modify the alloy of Al-Si used is antimony (Sb). The article examines the possible effect of the modification that element and heat treatment on the final tool wear after machining of the alloy AlSi9CuMnNi. In the experiments were made three castings from the alloy AlSi9CuMnNi without modification, three castings with the modification and without heat treatment, three castings with modification and without heat treatment, and three castings with modification and heat treatment too. These all castings were machining by turning with the same cutting conditions and next the tool wear of using inserts was analyzed. The described experiments and analysis are part of extensive research, focusing on a Faculty of Production Technology and Management, J. E. Purkyne University in Usti nad Labem.

Název v anglickém jazyce

Modification of AlSi9CuMnNi alloy by antimony and heat treatment and their influence on tool wear after turning

Popis výsledku anglicky

Modification alloy is an important part of the metallurgical process, and this also applies, of course, for aluminum alloys, particularly for Al-Si (silumins). As a modification of the material we can use the modification using the selected element or heat treatment of alloys, or a combination of both processes. One of the elements that it is possible to modify the alloy of Al-Si used is antimony (Sb). The article examines the possible effect of the modification that element and heat treatment on the final tool wear after machining of the alloy AlSi9CuMnNi. In the experiments were made three castings from the alloy AlSi9CuMnNi without modification, three castings with the modification and without heat treatment, three castings with modification and without heat treatment, and three castings with modification and heat treatment too. These all castings were machining by turning with the same cutting conditions and next the tool wear of using inserts was analyzed. The described experiments and analysis are part of extensive research, focusing on a Faculty of Production Technology and Management, J. E. Purkyne University in Usti nad Labem.

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JG - Hutnictví, kovové materiály

OECD FORD obor

—

Projekt

—

Návaznosti

V - Vyzkumna aktivita podporovana z jinych verejnych zdroju

Rok uplatnění

2016

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Manufacturing Technology

ISSN

1213-2489

e-ISSN

—

Svazek periodika

16

Číslo periodika v rámci svazku

1

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

6

Strana od-do

209-214

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—