Using of the electron microscope to evaluate the tool wear for a selected cutting insert

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F44555601%3A13420%2F18%3A43894114" target="_blank" >RIV/44555601:13420/18:43894114 - isvavai.cz</a>

Výsledek na webu

<a href="http://dx.doi.org/10.21062/ujep/152.2018/a/1213-2489/MT/18/4/635" target="_blank" >http://dx.doi.org/10.21062/ujep/152.2018/a/1213-2489/MT/18/4/635</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.21062/ujep/152.2018/a/1213-2489/MT/18/4/635" target="_blank" >10.21062/ujep/152.2018/a/1213-2489/MT/18/4/635</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Using of the electron microscope to evaluate the tool wear for a selected cutting insert

Popis výsledku v původním jazyce

Using of cutting inserts is currently a normal part of the manufacturing process. The article deals with analysis of tool wear after machining at one selected cutting insert. Evaluation of this insert was made by electron microscopy. There was used SEM and EDS analysis. For this purpose was used scanning electron microscope Tescan Vega 3 and EDS analyzer Bruker 16 which is part of this microscope. These analysis can provide a good picture of the structure and construction of inserts, their composition and for situation on the insert after machining. This may assist in finding suitable cutting conditions. As experimental material the hardened steel class 16MnCr5 according to EN 10027-1 has been machining. SEM images of final tool wear of the cutting insert were recorded. The reason was to map the tool wear state after machining using electron microscopy to give a better view of the situation. These analyzes were performed in other experiments performed at the Faculty of Mechanical Engineering at Jan Evangelista Purkyne University in ústí nad Labem. (C) 2018. Published by Manufacturing Technology.

Název v anglickém jazyce

Using of the electron microscope to evaluate the tool wear for a selected cutting insert

Popis výsledku anglicky

Using of cutting inserts is currently a normal part of the manufacturing process. The article deals with analysis of tool wear after machining at one selected cutting insert. Evaluation of this insert was made by electron microscopy. There was used SEM and EDS analysis. For this purpose was used scanning electron microscope Tescan Vega 3 and EDS analyzer Bruker 16 which is part of this microscope. These analysis can provide a good picture of the structure and construction of inserts, their composition and for situation on the insert after machining. This may assist in finding suitable cutting conditions. As experimental material the hardened steel class 16MnCr5 according to EN 10027-1 has been machining. SEM images of final tool wear of the cutting insert were recorded. The reason was to map the tool wear state after machining using electron microscopy to give a better view of the situation. These analyzes were performed in other experiments performed at the Faculty of Mechanical Engineering at Jan Evangelista Purkyne University in ústí nad Labem. (C) 2018. Published by Manufacturing Technology.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/ED4.1.00%2F11.0260" target="_blank" >ED4.1.00/11.0260: Zkvalitnění vzdělávání a rozšíření výzkumu na FVTM</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2018

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Manufacturing Technology

ISSN

1213-2489

e-ISSN

—

Svazek periodika

18

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

6

Strana od-do

635-640

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85058061648