Analysis of the Increased Iron Content on the Corrosion Resistance of the AlSi7Mg0.3 Alloy Casting

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F44555601%3A13420%2F19%3A43895025" target="_blank" >RIV/44555601:13420/19:43895025 - isvavai.cz</a>

Výsledek na webu

<a href="https://arl.ujep.cz/arl-ujep/en/csg/?repo=ujeprepo&key=45256193013" target="_blank" >https://arl.ujep.cz/arl-ujep/en/csg/?repo=ujeprepo&key=45256193013</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.21062/ujep/415.2019/a/1213-2489/MT/19/6/1041" target="_blank" >10.21062/ujep/415.2019/a/1213-2489/MT/19/6/1041</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Analysis of the Increased Iron Content on the Corrosion Resistance of the AlSi7Mg0.3 Alloy Casting

Popis výsledku v původním jazyce

Aluminium alloys are, due to their properties, an important part of all shaped castings made especially for the aerospace and automotive industry. One of the widely used alloys, for the production of castings in the automotive industry, is the AlSi7Mg0.3 alloy. In the experiment, which is the content of this paper, two castings from AlSi7Mg0.3 alloy were tested. Iron is a common contaminant in aluminium alloys and its content in the alloy is increased by the use of secondary aluminium alloys or by various causes during the production process itself. In the experiment, the corrosion resistance of castings was evaluated (in one of them the increased Fe content) under the specified conditions in the corrosion chamber with salt mist. Corrosion properties were evaluated using confo-cal laser microscopy. Based on the results of the microscopic analysis, the relevant conclusions were formulated. From the experiment, it is evident that the increased iron content (0.319 [wt. %]) does not, in this case, affect the corrosion resistance of casting.

Název v anglickém jazyce

Analysis of the Increased Iron Content on the Corrosion Resistance of the AlSi7Mg0.3 Alloy Casting

Popis výsledku anglicky

Aluminium alloys are, due to their properties, an important part of all shaped castings made especially for the aerospace and automotive industry. One of the widely used alloys, for the production of castings in the automotive industry, is the AlSi7Mg0.3 alloy. In the experiment, which is the content of this paper, two castings from AlSi7Mg0.3 alloy were tested. Iron is a common contaminant in aluminium alloys and its content in the alloy is increased by the use of secondary aluminium alloys or by various causes during the production process itself. In the experiment, the corrosion resistance of castings was evaluated (in one of them the increased Fe content) under the specified conditions in the corrosion chamber with salt mist. Corrosion properties were evaluated using confo-cal laser microscopy. Based on the results of the microscopic analysis, the relevant conclusions were formulated. From the experiment, it is evident that the increased iron content (0.319 [wt. %]) does not, in this case, affect the corrosion resistance of casting.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20501 - Materials engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Manufacturing Technology

ISSN

1213-2489

e-ISSN

—

Svazek periodika

19

Číslo periodika v rámci svazku

6

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

6

Strana od-do

1041-1046

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85077809833