Noise and Vibration Analysis of Conveyor Belt

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F44555601%3A13420%2F19%3A43895100" target="_blank" >RIV/44555601:13420/19:43895100 - isvavai.cz</a>

Výsledek na webu

<a href="https://arl.ujep.cz/arl-ujep/cs/csg/?repo=ujeprepo&key=26974835191" target="_blank" >https://arl.ujep.cz/arl-ujep/cs/csg/?repo=ujeprepo&key=26974835191</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.21062/ujep/341.2019/a/1213-2489/MT/19/4/604" target="_blank" >10.21062/ujep/341.2019/a/1213-2489/MT/19/4/604</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Noise and Vibration Analysis of Conveyor Belt

Popis výsledku v původním jazyce

The article deals with the measurement of conveyor belt noise and vibration. The conveyor belt was supported on six rollers fixed on three plates of stand, return and drive drum. These six rollers were produced in two sets (convectional tube and accurate tube). Rollers were driven by a rubber belt. The noise was measured and evaluated on both sides of the conveyor. Vibration of the conveyor was measured at four locations of the conveyor construction. All measurements were performed in an unloaded condition. In conclusion of the article is a summary and evaluation of all measurements. The vibration of the conveyor is comparable in both cases, however, the rollers from accuracy tube excite the construction less, and this results in a lower total noise. By comparing the acceleration to the dominant frequency, it is obvious that the noise and the vibration of the belt conveyor construction were reduced by using rollers from accuracy tube.

Název v anglickém jazyce

Noise and Vibration Analysis of Conveyor Belt

Popis výsledku anglicky

The article deals with the measurement of conveyor belt noise and vibration. The conveyor belt was supported on six rollers fixed on three plates of stand, return and drive drum. These six rollers were produced in two sets (convectional tube and accurate tube). Rollers were driven by a rubber belt. The noise was measured and evaluated on both sides of the conveyor. Vibration of the conveyor was measured at four locations of the conveyor construction. All measurements were performed in an unloaded condition. In conclusion of the article is a summary and evaluation of all measurements. The vibration of the conveyor is comparable in both cases, however, the rollers from accuracy tube excite the construction less, and this results in a lower total noise. By comparing the acceleration to the dominant frequency, it is obvious that the noise and the vibration of the belt conveyor construction were reduced by using rollers from accuracy tube.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2019

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Manufacturing Technology

ISSN

1213-2489

e-ISSN

—

Svazek periodika

2019

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

5

Strana od-do

604-608

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85077150242