Quality Evaluation of Welding Joints by Different Methods

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F44555601%3A13420%2F20%3A43895808" target="_blank" >RIV/44555601:13420/20:43895808 - isvavai.cz</a>

Výsledek na webu

<a href="https://scindeks-clanci.ceon.rs/data/pdf/1451-2092/2020/1451-20922004816Q.pdf" target="_blank" >https://scindeks-clanci.ceon.rs/data/pdf/1451-2092/2020/1451-20922004816Q.pdf</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.5937/fme2004816T" target="_blank" >10.5937/fme2004816T</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Quality Evaluation of Welding Joints by Different Methods

Popis výsledku v původním jazyce

This paper presents the results of the quality evaluation of the weld joints on welded pipes used in industrial energy. The quality evaluation of the weld joints was performed by two methods. Using technical methods, welding faults and defects were examined, identified and evaluated by a metallographic analysis on the macrostructure of welds. According to ISO 6520-1:2007, the faults and defects were detected and classified into the group and classified into quality levels using ISO 5817:2008-03. Two quality management tools using a Cause and effect diagram - Iskihawa diagram and a Pareto diagram also evaluated the quality control of welds. These two tools enabled to identify the causes of welding defects as well as to determine the frequency of their occurrence and to identify the most serious welding faults and defects. Both methods - technical and management, should reveal shortcomings in both technical, technological and personnel aspect. Their use should contribute to improving the welding process of pipes in operation and to increasing the safety of piping systems.

Název v anglickém jazyce

Quality Evaluation of Welding Joints by Different Methods

Popis výsledku anglicky

This paper presents the results of the quality evaluation of the weld joints on welded pipes used in industrial energy. The quality evaluation of the weld joints was performed by two methods. Using technical methods, welding faults and defects were examined, identified and evaluated by a metallographic analysis on the macrostructure of welds. According to ISO 6520-1:2007, the faults and defects were detected and classified into the group and classified into quality levels using ISO 5817:2008-03. Two quality management tools using a Cause and effect diagram - Iskihawa diagram and a Pareto diagram also evaluated the quality control of welds. These two tools enabled to identify the causes of welding defects as well as to determine the frequency of their occurrence and to identify the most serious welding faults and defects. Both methods - technical and management, should reveal shortcomings in both technical, technological and personnel aspect. Their use should contribute to improving the welding process of pipes in operation and to increasing the safety of piping systems.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

—

Návaznosti

N - Vyzkumna aktivita podporovana z neverejnych zdroju

Rok uplatnění

2020

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

FME Transactions

ISSN

1451-2092

e-ISSN

—

Svazek periodika

48

Číslo periodika v rámci svazku

4

Stát vydavatele periodika

RS - Srbská republika

Počet stran výsledku

9

Strana od-do

816-824

Kód UT WoS článku

000576413500011

EID výsledku v databázi Scopus

2-s2.0-85096002481