Experimental analysis of microhardness changes of subsurface areas affected by WEDM

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F44555601%3A13420%2F22%3A43897255" target="_blank" >RIV/44555601:13420/22:43897255 - isvavai.cz</a>

Nalezeny alternativní kódy

RIV/00216305:26210/22:PU144246 RIV/68081731:_____/22:00561101 RIV/61989100:27230/22:10249449

Výsledek na webu

<a href="https://journals.sagepub.com/doi/full/10.1177/09544089221078383" target="_blank" >https://journals.sagepub.com/doi/full/10.1177/09544089221078383</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1177/09544089221078383" target="_blank" >10.1177/09544089221078383</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Experimental analysis of microhardness changes of subsurface areas affected by WEDM

Popis výsledku v původním jazyce

The influence of the surface area by the impact of high temperatures after wire electric discharge machining (WEDM) is a known fact. However, the affected parameters also include a change in microhardness. In order to further investigate this statement, 5 different ferrous and non-ferrous materials were selected, from which three samples were always made with different settings of machine parameters (gap voltage, pulse on and off time, wire feed and discharge current). This examined not only the effect of the machining itself on the material but also whether the change in the microhardness of the material is affected by the setting of the machine parameters. In order to measure the microhardness of the subsurface layer, a metallographic preparation was made from each sample, which enabled accurate measurements always in the same area. Subsequent evaluation revealed that the microhardness may not be affected at all and everything depends only on the type of material being machined. The changes in microhardness affected by setting machine parameters are negligible.

Název v anglickém jazyce

Experimental analysis of microhardness changes of subsurface areas affected by WEDM

Popis výsledku anglicky

The influence of the surface area by the impact of high temperatures after wire electric discharge machining (WEDM) is a known fact. However, the affected parameters also include a change in microhardness. In order to further investigate this statement, 5 different ferrous and non-ferrous materials were selected, from which three samples were always made with different settings of machine parameters (gap voltage, pulse on and off time, wire feed and discharge current). This examined not only the effect of the machining itself on the material but also whether the change in the microhardness of the material is affected by the setting of the machine parameters. In order to measure the microhardness of the subsurface layer, a metallographic preparation was made from each sample, which enabled accurate measurements always in the same area. Subsequent evaluation revealed that the microhardness may not be affected at all and everything depends only on the type of material being machined. The changes in microhardness affected by setting machine parameters are negligible.

Druh

J_imp - Článek v periodiku v databázi Web of Science

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/EF18_069%2F0010045" target="_blank" >EF18_069/0010045: Vývoj nových nano a mikro povlaků na povrchu vybraných kovových materiálů - NANOTECH ITI II</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2022

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering

ISSN

0954-4089

e-ISSN

2041-3009

Svazek periodika

236

Číslo periodika v rámci svazku

5

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

13

Strana od-do

1979-1991

Kód UT WoS článku

000758692600001

EID výsledku v databázi Scopus

2-s2.0-85125081209