Comparison of performance of austrian made si3n4 - nitride ceramic tools used to machine grey cast iron workpiece materials
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F46747885%3A24210%2F09%3A%230001133" target="_blank" >RIV/46747885:24210/09:#0001133 - isvavai.cz</a>
Nalezeny alternativní kódy
RIV/46747885:24210/09:#0001459
Výsledek na webu
—
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Comparison of performance of austrian made si3n4 - nitride ceramic tools used to machine grey cast iron workpiece materials
Popis výsledku v původním jazyce
This article presents comparisons of cutting performance of Austrian made ? Si3N4 nitride ceramic ? inserts used in machining a Type 422425 grey cast iron work-piece materials. Three commercial ceramic inserts Type FMG121C, FMG122C, and FMG134C were tested. Experiments were focused on tool life tests. A comparison approach involved exponents of Taylor?s type equations over an optimized cutting tool interval i.e. one constant depth of cut of 1mm, one constant feed rate of 0.2mm/rev and the three cuttingspeeds 250, 320 and 380m/min. Results were obtained from linear regression. Also conducted was an evaluation of intervals of reliability as well as corresponding standard deviations for each regression coefficient in experimental Taylor?s equations. Theexperiments allowed to compare, from statistical perspectives, at a 95 and greater confidence level, the trends and quantities of experimental cutting inserts.
Název v anglickém jazyce
Comparison of performance of austrian made si3n4 - nitride ceramic tools used to machine grey cast iron workpiece materials
Popis výsledku anglicky
This article presents comparisons of cutting performance of Austrian made ? Si3N4 nitride ceramic ? inserts used in machining a Type 422425 grey cast iron work-piece materials. Three commercial ceramic inserts Type FMG121C, FMG122C, and FMG134C were tested. Experiments were focused on tool life tests. A comparison approach involved exponents of Taylor?s type equations over an optimized cutting tool interval i.e. one constant depth of cut of 1mm, one constant feed rate of 0.2mm/rev and the three cuttingspeeds 250, 320 and 380m/min. Results were obtained from linear regression. Also conducted was an evaluation of intervals of reliability as well as corresponding standard deviations for each regression coefficient in experimental Taylor?s equations. Theexperiments allowed to compare, from statistical perspectives, at a 95 and greater confidence level, the trends and quantities of experimental cutting inserts.
Klasifikace
Druh
J<sub>x</sub> - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JR - Ostatní strojírenství
OECD FORD obor
—
Návaznosti výsledku
Projekt
<a href="/cs/project/FT-TA4%2F105" target="_blank" >FT-TA4/105: *Integrita povrchu ( IP ) jako nástroj pro zvyšování užitných vlastností součástí vyráběných na strojích TOS VARNSDORF a.s.</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)<br>Z - Vyzkumny zamer (s odkazem do CEZ)
Ostatní
Rok uplatnění
2009
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Modern Machinery Science Journal
ISSN
1803-1269
e-ISSN
—
Svazek periodika
2009
Číslo periodika v rámci svazku
october
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
3
Strana od-do
—
Kód UT WoS článku
—
EID výsledku v databázi Scopus
—