Simulation Calculation of Solidification and Cooling of Copper Alloys casts
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F46747885%3A24210%2F15%3A00002421" target="_blank" >RIV/46747885:24210/15:00002421 - isvavai.cz</a>
Výsledek na webu
<a href="https://www.researchgate.net/publication/287224267_Simulation_calculations_of_solidification_and_cooling_of_copper_alloy_casts" target="_blank" >https://www.researchgate.net/publication/287224267_Simulation_calculations_of_solidification_and_cooling_of_copper_alloy_casts</a>
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Simulation Calculation of Solidification and Cooling of Copper Alloys casts
Popis výsledku v původním jazyce
The article deals with the simulation calculation of solidification and cooling of plate-shaped castings cast into metal and into sand mould about cavity dimensional 80 x 80 x 10 mm. During the experiments were monitored conditiouns of filling, solidification and cooling in the die-cast (metal mould) and in the sand mould. Both about outer dimensions 120 x 120 x 80 mm. Die-mould was made of steel 1.2343 (ČWSN 19552) and sand mould was prepared of green sand (bentonite). For the purse of the experiments was used foundry simulation software MAGMA 5. For simulation calculations were used thermo-physical quantities in dependence on temperature. Concureently were used knowledges of the simulation calculations performed at our department, Department of Engineering Technology, Faculty of Mechanical Engineering - Technical University of Liberec.
Název v anglickém jazyce
Simulation Calculation of Solidification and Cooling of Copper Alloys casts
Popis výsledku anglicky
The article deals with the simulation calculation of solidification and cooling of plate-shaped castings cast into metal and into sand mould about cavity dimensional 80 x 80 x 10 mm. During the experiments were monitored conditiouns of filling, solidification and cooling in the die-cast (metal mould) and in the sand mould. Both about outer dimensions 120 x 120 x 80 mm. Die-mould was made of steel 1.2343 (ČWSN 19552) and sand mould was prepared of green sand (bentonite). For the purse of the experiments was used foundry simulation software MAGMA 5. For simulation calculations were used thermo-physical quantities in dependence on temperature. Concureently were used knowledges of the simulation calculations performed at our department, Department of Engineering Technology, Faculty of Mechanical Engineering - Technical University of Liberec.
Klasifikace
Druh
J<sub>SC</sub> - Článek v periodiku v databázi SCOPUS
CEP obor
—
OECD FORD obor
20501 - Materials engineering
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2015
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Manufacturing Technology
ISSN
1213-2489
e-ISSN
—
Svazek periodika
15
Číslo periodika v rámci svazku
4
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
6
Strana od-do
591-596
Kód UT WoS článku
—
EID výsledku v databázi Scopus
2-s2.0-84949201421