Impact of stitch length on sewing needle temperature

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F46747885%3A24410%2F14%3A%230004026" target="_blank" >RIV/46747885:24410/14:#0004026 - isvavai.cz</a>

Výsledek na webu

<a href="http://multi-science.metapress.com/content/61x567h250554574/?p=8de6d0ff743b4200997fdea7403ceaec&pi=12" target="_blank" >http://multi-science.metapress.com/content/61x567h250554574/?p=8de6d0ff743b4200997fdea7403ceaec&pi=12</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1260/1708-5284.11.2.187" target="_blank" >10.1260/1708-5284.11.2.187</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Impact of stitch length on sewing needle temperature

Popis výsledku v původním jazyce

In this article the sewing needle heat is measured without sewing thread and with sewing thread at different stitch density (stitches per inch or SPI) of lock stitch sewing machine by thermocouples. Two methods are used to measure sewing needle heat, touch thermocouple method and inserted thermo couple method. Needle temperature is measured after periodic 10, 20, 30 and 60 seconds of sewing operation. Whereas the machine running at speed from 1000 r/m to 4700 r/m. It is observed that decreasing stitch length causes an increase in the temperature of the sewing needle. Stitch density shows same influence on needle for sewing with thread and without thread. It is observed from our research that at SPI of 14 the needle temperature with thread rises to 259oC at 4000 r/min of machine. It is recommended to use minimum stitch density.

Název v anglickém jazyce

Impact of stitch length on sewing needle temperature

Popis výsledku anglicky

In this article the sewing needle heat is measured without sewing thread and with sewing thread at different stitch density (stitches per inch or SPI) of lock stitch sewing machine by thermocouples. Two methods are used to measure sewing needle heat, touch thermocouple method and inserted thermo couple method. Needle temperature is measured after periodic 10, 20, 30 and 60 seconds of sewing operation. Whereas the machine running at speed from 1000 r/m to 4700 r/m. It is observed that decreasing stitch length causes an increase in the temperature of the sewing needle. Stitch density shows same influence on needle for sewing with thread and without thread. It is observed from our research that at SPI of 14 the needle temperature with thread rises to 259oC at 4000 r/min of machine. It is recommended to use minimum stitch density.

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

JJ - Ostatní materiály

OECD FORD obor

—

Projekt

—

Návaznosti

S - Specificky vyzkum na vysokych skolach

Rok uplatnění

2014

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

World Journal of Engineering

ISSN

1708-5284

e-ISSN

—

Svazek periodika

11

Číslo periodika v rámci svazku

2

Stát vydavatele periodika

GB - Spojené království Velké Británie a Severního Irska

Počet stran výsledku

6

Strana od-do

187-192

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—