Nanocellulose coated woven jute/green epoxy composites: Characterization of mechanical and dynamic mechanical behavior
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F46747885%3A24410%2F17%3A00003740" target="_blank" >RIV/46747885:24410/17:00003740 - isvavai.cz</a>
Výsledek na webu
<a href="https://www.sciencedirect.com/science/article/pii/S0263822316319961?via=ihub" target="_blank" >https://www.sciencedirect.com/science/article/pii/S0263822316319961?via=ihub</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.1016/j.compstruct.2016.11.062" target="_blank" >10.1016/j.compstruct.2016.11.062</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Nanocellulose coated woven jute/green epoxy composites: Characterization of mechanical and dynamic mechanical behavior
Popis výsledku v původním jazyce
This paper presents the preparation and characterization of nanocellulose coated woven jute/green epoxycomposites. Waste jute fibers were used as precursor to purify and extract nanocellulose by chemicaltreatments. The prepared suspensions with 3, 5 and 10 wt% of nanocellulose were coated over jute fabricfollowed by preparation of composites by compression molding technique. The surface morphologies oftreated jute fibers, jute cellulose nanofibrils (CNF), nanocellulose coated jute fabrics and fractured surfaces of composites were characterized by scanning electron microscopy (SEM). The crystallinity of jutefibers after different chemical treatments was measured by X-ray diffraction (XRD). The effect of nanocellulose coating over jute reinforcement on the tensile, flexural, fracture toughness and dynamic mechanical properties of prepared composites has been investigated. Fracture toughness was measured usingsingle end notched bend (SENB) specimens and dynamic mechanical test was performed in three pointbending mode. The results revealed the improvement in tensile modulus, flexural properties and fracturetoughness except the decrease in tensile strength of nanocellulose coated woven jute/green epoxy composites as compared to uncoated jute composite. Dynamic mechanical analysis (DMA) results alsoshowed the increase in storage modulus and reduction in tangent delta peak height of nanocellulosecoated jute composites.
Název v anglickém jazyce
Nanocellulose coated woven jute/green epoxy composites: Characterization of mechanical and dynamic mechanical behavior
Popis výsledku anglicky
This paper presents the preparation and characterization of nanocellulose coated woven jute/green epoxycomposites. Waste jute fibers were used as precursor to purify and extract nanocellulose by chemicaltreatments. The prepared suspensions with 3, 5 and 10 wt% of nanocellulose were coated over jute fabricfollowed by preparation of composites by compression molding technique. The surface morphologies oftreated jute fibers, jute cellulose nanofibrils (CNF), nanocellulose coated jute fabrics and fractured surfaces of composites were characterized by scanning electron microscopy (SEM). The crystallinity of jutefibers after different chemical treatments was measured by X-ray diffraction (XRD). The effect of nanocellulose coating over jute reinforcement on the tensile, flexural, fracture toughness and dynamic mechanical properties of prepared composites has been investigated. Fracture toughness was measured usingsingle end notched bend (SENB) specimens and dynamic mechanical test was performed in three pointbending mode. The results revealed the improvement in tensile modulus, flexural properties and fracturetoughness except the decrease in tensile strength of nanocellulose coated woven jute/green epoxy composites as compared to uncoated jute composite. Dynamic mechanical analysis (DMA) results alsoshowed the increase in storage modulus and reduction in tangent delta peak height of nanocellulosecoated jute composites.
Klasifikace
Druh
J<sub>imp</sub> - Článek v periodiku v databázi Web of Science
CEP obor
—
OECD FORD obor
20505 - Composites (including laminates, reinforced plastics, cermets, combined natural and synthetic fibre fabrics; filled composites)
Návaznosti výsledku
Projekt
—
Návaznosti
S - Specificky vyzkum na vysokych skolach
Ostatní
Rok uplatnění
2017
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Composite Structures
ISSN
0263-8223
e-ISSN
—
Svazek periodika
161
Číslo periodika v rámci svazku
February
Stát vydavatele periodika
GB - Spojené království Velké Británie a Severního Irska
Počet stran výsledku
10
Strana od-do
340-349
Kód UT WoS článku
000390471700030
EID výsledku v databázi Scopus
2-s2.0-84998890730