Experimental Verification of an Analytical Model for the Ring-shaped Piezoelectric Transformer

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F46747885%3A24510%2F15%3A%230001211" target="_blank" >RIV/46747885:24510/15:#0001211 - isvavai.cz</a>

Výsledek na webu

<a href="http://electroinf.uoradea.ro/images/articles/CERCETARE/Reviste/JEEE/JEEE_V8_N2_OCT_2015/Pulpan-JEEE_Vol_8_Nr_2_OCT_2015.pdf" target="_blank" >http://electroinf.uoradea.ro/images/articles/CERCETARE/Reviste/JEEE/JEEE_V8_N2_OCT_2015/Pulpan-JEEE_Vol_8_Nr_2_OCT_2015.pdf</a>

DOI - Digital Object Identifier

—

Jazyk výsledku

angličtina

Název v původním jazyce

Experimental Verification of an Analytical Model for the Ring-shaped Piezoelectric Transformer

Popis výsledku v původním jazyce

Piezoelectric transformers prepared using bulk PZT ceramic rings poled homogeneously along thickness were studied experimentally on the commercially available rings (PZT type APC841, d =20 mm, D = 50 mm and thickness 6 mm, aspect ratio d/D = 0.40) as well as analytically. Input and output parts were formed by the concentric ring electrodes. The fundamental and the first overtone were measured for the transformation ratio and efficiency. Ring transformer geometry shows the high transformation ratios (upto 108 under no-load condition for the first overtone) and efficiencies 91-99% for the properly designed electrode diameter. The optimum resistive load was relatively small within the range of 0.1 ? 5kOhm. The optimum aspect ratio of electrode was foundas d1/D = 0.70. The fundamental resonance frequency was found insensitive to the electrode diameter contrary to the first overtone. Analytical calculations are also used for the comparison of the mechanically free and clamped transformer.

Název v anglickém jazyce

Experimental Verification of an Analytical Model for the Ring-shaped Piezoelectric Transformer

Popis výsledku anglicky

Piezoelectric transformers prepared using bulk PZT ceramic rings poled homogeneously along thickness were studied experimentally on the commercially available rings (PZT type APC841, d =20 mm, D = 50 mm and thickness 6 mm, aspect ratio d/D = 0.40) as well as analytically. Input and output parts were formed by the concentric ring electrodes. The fundamental and the first overtone were measured for the transformation ratio and efficiency. Ring transformer geometry shows the high transformation ratios (upto 108 under no-load condition for the first overtone) and efficiencies 91-99% for the properly designed electrode diameter. The optimum resistive load was relatively small within the range of 0.1 ? 5kOhm. The optimum aspect ratio of electrode was foundas d1/D = 0.70. The fundamental resonance frequency was found insensitive to the electrode diameter contrary to the first overtone. Analytical calculations are also used for the comparison of the mechanically free and clamped transformer.

Druh

J_x - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)

CEP obor

BM - Fyzika pevných látek a magnetismus

OECD FORD obor

—

Projekt

<a href="/cs/project/GAP102%2F10%2F1139" target="_blank" >GAP102/10/1139: Piezoelektrické transformátory, jejich design a parametry</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2015

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Journal of Electrical and Electronics Engineering

ISSN

1844-6035

e-ISSN

—

Svazek periodika

8

Číslo periodika v rámci svazku

2

Stát vydavatele periodika

RO - Rumunsko

Počet stran výsledku

6

Strana od-do

23-28

Kód UT WoS článku

—

EID výsledku v databázi Scopus

—