Surface roughness evaluation after machining wear resistant hard coats

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23210%2F17%3A43950751" target="_blank" >RIV/49777513:23210/17:43950751 - isvavai.cz</a>

Výsledek na webu

<a href="https://www.matec-conferences.org/articles/matecconf/pdf/2017/51/matecconf_mtem2017_03008.pdf" target="_blank" >https://www.matec-conferences.org/articles/matecconf/pdf/2017/51/matecconf_mtem2017_03008.pdf</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1051/matecconf/201713703008" target="_blank" >10.1051/matecconf/201713703008</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Surface roughness evaluation after machining wear resistant hard coats

Popis výsledku v původním jazyce

The technology HVOF - High Velocity Oxygen Fuel was used to spray the alloy Stellite 6 for the purpose of this research. This method is based on using high velocity spraying flame. The article deals with the evaluation of surface quality after machining of wear resistant hard coats. The goal of the authors was to understand the main factors that influence final surface quality at machining of the coatings from Stellite 6. The findings of experiment have confirmed that there have been obtained very important information about machining of this alloy at the specific type of workpiece. Authors have evaluated the quality of the surface not only by means of Abbott curve, but they have also observed the dependency of arithmetical mean roughness value on both cutting edge radius and feed. The analyses of cutting tips wear at changeable inserts of tools have shown that the typical wear appears in the form of a notch.

Název v anglickém jazyce

Surface roughness evaluation after machining wear resistant hard coats

Popis výsledku anglicky

The technology HVOF - High Velocity Oxygen Fuel was used to spray the alloy Stellite 6 for the purpose of this research. This method is based on using high velocity spraying flame. The article deals with the evaluation of surface quality after machining of wear resistant hard coats. The goal of the authors was to understand the main factors that influence final surface quality at machining of the coatings from Stellite 6. The findings of experiment have confirmed that there have been obtained very important information about machining of this alloy at the specific type of workpiece. Authors have evaluated the quality of the surface not only by means of Abbott curve, but they have also observed the dependency of arithmetical mean roughness value on both cutting edge radius and feed. The analyses of cutting tips wear at changeable inserts of tools have shown that the typical wear appears in the form of a notch.

Druh

D - Stať ve sborníku

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/ED2.1.00%2F03.0093" target="_blank" >ED2.1.00/03.0093: Regionální technologický institut - RTI</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2017

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Modern Technologies in Manufacturing (MTeM 2017 - AMaTUC)

ISBN

978-2-7598-9027-9

ISSN

2261-236X

e-ISSN

neuvedeno

Počet stran výsledku

8

Strana od-do

1-8

Název nakladatele

EDP Sciences

Místo vydání

Neuveden

Místo konání akce

Cluj-Napoca; Romania

Datum konání akce

12. 10. 2017

Typ akce podle státní příslušnosti

EUR - Evropská akce

Kód UT WoS článku

—