EFFECT OF SCANNING SPEED WHEN MEASURING SURFACE ROUGHNESS
Identifikátory výsledku
Kód výsledku v IS VaVaI
<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23210%2F18%3A43953176" target="_blank" >RIV/49777513:23210/18:43953176 - isvavai.cz</a>
Výsledek na webu
<a href="http://www.daaam.info/Downloads/Pdfs/proceedings/proceedings_2018/180.pdf" target="_blank" >http://www.daaam.info/Downloads/Pdfs/proceedings/proceedings_2018/180.pdf</a>
DOI - Digital Object Identifier
<a href="http://dx.doi.org/10.2507/29th.daaam.proceedings.180" target="_blank" >10.2507/29th.daaam.proceedings.180</a>
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
EFFECT OF SCANNING SPEED WHEN MEASURING SURFACE ROUGHNESS
Popis výsledku v původním jazyce
In the field of practical metrology it is extremely important not only accuracy but also the measurement of measuring productivity activities which entail considerable costs. Within this article, was tested the influence of the velocity for measuring of roughness. Test was made in in controlled laboratory conditions on the quality and accuracy of the measurements In this paper experiment described test that was performed on standard pieces with defined Ra and Rz values. The test was performed on the principle of repeated measurement at different speeds. The speed was 0.1-3 mm / s, which is the range of Hommel Etami T 8000. This machine is currently used for calibration at the Czech Metrology Institute and is one of the leading machines for measuring roughness in technical practice. The results obtained clearly declare the effect on the results of the measured values. All measured data underwent statistical processing and subsequently verification of its accuracy.
Název v anglickém jazyce
EFFECT OF SCANNING SPEED WHEN MEASURING SURFACE ROUGHNESS
Popis výsledku anglicky
In the field of practical metrology it is extremely important not only accuracy but also the measurement of measuring productivity activities which entail considerable costs. Within this article, was tested the influence of the velocity for measuring of roughness. Test was made in in controlled laboratory conditions on the quality and accuracy of the measurements In this paper experiment described test that was performed on standard pieces with defined Ra and Rz values. The test was performed on the principle of repeated measurement at different speeds. The speed was 0.1-3 mm / s, which is the range of Hommel Etami T 8000. This machine is currently used for calibration at the Czech Metrology Institute and is one of the leading machines for measuring roughness in technical practice. The results obtained clearly declare the effect on the results of the measured values. All measured data underwent statistical processing and subsequently verification of its accuracy.
Klasifikace
Druh
D - Stať ve sborníku
CEP obor
—
OECD FORD obor
20301 - Mechanical engineering
Návaznosti výsledku
Projekt
<a href="/cs/project/LO1502" target="_blank" >LO1502: Rozvoj Regionálního technologického institutu</a><br>
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2018
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název statě ve sborníku
Annals of DAAAM and Proceedings of the International DAAAM Symposium
ISBN
978-3-902734-20-4
ISSN
1726-9679
e-ISSN
neuvedeno
Počet stran výsledku
7
Strana od-do
1249-1255
Název nakladatele
DAAAM International Vienna
Místo vydání
Vídeň, Rakousko
Místo konání akce
Zadar, Croatia EU
Datum konání akce
24. 10. 2018
Typ akce podle státní příslušnosti
EUR - Evropská akce
Kód UT WoS článku
—