Influence of grinding conditions and tilting the spindle on the spindle load when a 5-axis grinder is used

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23210%2F18%3A43953820" target="_blank" >RIV/49777513:23210/18:43953820 - isvavai.cz</a>

Výsledek na webu

<a href="https://arl.ujep.cz/arl-ujep/en/csg/?repo=ujeprepo&key=53129063325" target="_blank" >https://arl.ujep.cz/arl-ujep/en/csg/?repo=ujeprepo&key=53129063325</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.21062/ujep/299.2019/a/1213-2489/mt/19/3/375" target="_blank" >10.21062/ujep/299.2019/a/1213-2489/mt/19/3/375</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Influence of grinding conditions and tilting the spindle on the spindle load when a 5-axis grinder is used

Popis výsledku v původním jazyce

This article deals with the influence of grinding conditions and tilting the spindle on changes in the spindle load when grinding tool steel on a 5-axis tool grinding machine. The experiment was designed to investigate any changes in cutting speed, feed rate or tilting of the spindle. The size of the load is very important, because the load can influence the tool life, the life of the machine components, quality of the surfaces and dimensional accuracy of the components. A medical femoral knee replacement was selected as the semi-finished component for the experiment, as its surface is a good representative of a complex-shaped surface. This article is limited only to the grinding of maraging steel MS1 with a CBN grinding wheel. The second part of this article is focused on the experiment where the spindle load is evaluated and the results of the experiments are compared.

Název v anglickém jazyce

Influence of grinding conditions and tilting the spindle on the spindle load when a 5-axis grinder is used

Popis výsledku anglicky

This article deals with the influence of grinding conditions and tilting the spindle on changes in the spindle load when grinding tool steel on a 5-axis tool grinding machine. The experiment was designed to investigate any changes in cutting speed, feed rate or tilting of the spindle. The size of the load is very important, because the load can influence the tool life, the life of the machine components, quality of the surfaces and dimensional accuracy of the components. A medical femoral knee replacement was selected as the semi-finished component for the experiment, as its surface is a good representative of a complex-shaped surface. This article is limited only to the grinding of maraging steel MS1 with a CBN grinding wheel. The second part of this article is focused on the experiment where the spindle load is evaluated and the results of the experiments are compared.

Druh

J_SC - Článek v periodiku v databázi SCOPUS

CEP obor

—

OECD FORD obor

20301 - Mechanical engineering

Projekt

<a href="/cs/project/LO1502" target="_blank" >LO1502: Rozvoj Regionálního technologického institutu</a><br>

Návaznosti

P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)

Rok uplatnění

2018

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název periodika

Manufacturing Technology

ISSN

1213-2489

e-ISSN

—

Svazek periodika

19

Číslo periodika v rámci svazku

3

Stát vydavatele periodika

CZ - Česká republika

Počet stran výsledku

5

Strana od-do

375-379

Kód UT WoS článku

—

EID výsledku v databázi Scopus

2-s2.0-85069857436