Epoxy Resin Curing Process Evaluation Based on Signal Frequency Analysis from Interdigital Structure Sensor

Kód výsledku v IS VaVaI

<a href="https://www.isvavai.cz/riv?ss=detail&h=RIV%2F49777513%3A23220%2F10%3A43924972" target="_blank" >RIV/49777513:23220/10:43924972 - isvavai.cz</a>

Výsledek na webu

<a href="http://ieeexplore.ieee.org/stamp/stamp.jsp?tp=&arnumber=5642838" target="_blank" >http://ieeexplore.ieee.org/stamp/stamp.jsp?tp=&arnumber=5642838</a>

DOI - Digital Object Identifier

<a href="http://dx.doi.org/10.1109/ESTC.2010.5642838" target="_blank" >10.1109/ESTC.2010.5642838</a>

Jazyk výsledku

angličtina

Název v původním jazyce

Epoxy Resin Curing Process Evaluation Based on Signal Frequency Analysis from Interdigital Structure Sensor

Popis výsledku v původním jazyce

The epoxy resin curing is a chemical process that consists of several important steps within its curing time. These steps could be identified as gelation point, curing, vitrification and final solid state of the resin. These points of curing process areidentifiable by standard electrical measurement methods but the use of unique test equipment is necessary. Therefore, new possibilities of detection these important points of curing process are to be searched. All information about epoxy resin curing have to be known for correct technology process control. Based on that, it is necessary to analyze the curing process and to find its important curing points. During epoxy resin curing process some electrical parameters are changing. And here comes this newmethod into account. If a suitable sensor is placed in the epoxy resin during curing process then the above mentioned important points of curing process could be monitored and identified based on frequency analysis of signals from this s

Název v anglickém jazyce

Epoxy Resin Curing Process Evaluation Based on Signal Frequency Analysis from Interdigital Structure Sensor

Popis výsledku anglicky

The epoxy resin curing is a chemical process that consists of several important steps within its curing time. These steps could be identified as gelation point, curing, vitrification and final solid state of the resin. These points of curing process areidentifiable by standard electrical measurement methods but the use of unique test equipment is necessary. Therefore, new possibilities of detection these important points of curing process are to be searched. All information about epoxy resin curing have to be known for correct technology process control. Based on that, it is necessary to analyze the curing process and to find its important curing points. During epoxy resin curing process some electrical parameters are changing. And here comes this newmethod into account. If a suitable sensor is placed in the epoxy resin during curing process then the above mentioned important points of curing process could be monitored and identified based on frequency analysis of signals from this s

Druh

D - Stať ve sborníku

CEP obor

JB - Senzory, čidla, měření a regulace

OECD FORD obor

—

Projekt

—

Návaznosti

Z - Vyzkumny zamer (s odkazem do CEZ)

Rok uplatnění

2010

Kód důvěrnosti údajů

S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů

Název statě ve sborníku

Electronics System Integration Technology Conference ESTC 2010 in Berlin

ISBN

978-1-4244-8553-6

ISSN

—

e-ISSN

—

Počet stran výsledku

4

Strana od-do

1-4

Název nakladatele

IEEE

Místo vydání

Piscataway

Místo konání akce

Berlín

Datum konání akce

13. 9. 2010

Typ akce podle státní příslušnosti

WRD - Celosvětová akce

Kód UT WoS článku

—