Výpočtový model pro posouzení pevnosti ovíjeného kolíkového spoje kompozit/kov
Popis výsledku
Pevnost ovíjeného kolíkového spoje je závislá na mnoha parametrech. Zejména typ vláken či matrice, průměr kolíků a šířka či tloušťka ovinutí jsou parametry, jejichž vliv na pevnost spoje je nutné vyšetřit. Proto bylo cílem této práce vytvořit výpočtový model, pomocí kterého by bylo možné vyšetřit pevnost popisovaného spoje a tím umožnit návrh spojení požadovaných vlastností. Výpočtový model byl vytvořen v MKP systému MSC.Marc. Pro posouzení pevnosti bylo použito pevnostní kritérium LaRC04, které bylo dosystému MSC. Marc implementováno. Po srovnání výsledků z experimentů a numerických simulací bylo zjištěno, že kritérium LaRC04 je nutné modifikovat. Modifikací kritéria LaRC04 bylo získáno kritérium schopné s velkou přesností posuzovat pevnost IHPJ spojů v závislosti na rozměrech i materiálu spojovaných částí.
Klíčová slova
Identifikátory výsledku
Kód výsledku v IS VaVaI
Výsledek na webu
—
DOI - Digital Object Identifier
—
Alternativní jazyky
Jazyk výsledku
angličtina
Název v původním jazyce
Computational Model for Strength Analysis of Wrapped Pin Joint of Composite/Metal
Popis výsledku v původním jazyce
The strength of the wrapped pin joint depends on many parameters, especially on the type of the fibre or the resin, diameter of the pins, and width or thickness of the wrapping. Consequently, the aim of this work was to create the computational model, bywhich means it will be possible to investigate the strength of described joint, thereby make the joint of required properties possible to design. The computational model was created in FEM system MSC.Marc, where the recently implemented failure criterion LaRC04 was used. The comparison of the numerical and experimental results shows that it is necessary to modify the criterion LaRC04. By means of the modified criterion LaRC04 it is possible to investigate the strength of the IHPJ joint in dependence onthe geometry or the material with good accuracy.
Název v anglickém jazyce
Computational Model for Strength Analysis of Wrapped Pin Joint of Composite/Metal
Popis výsledku anglicky
The strength of the wrapped pin joint depends on many parameters, especially on the type of the fibre or the resin, diameter of the pins, and width or thickness of the wrapping. Consequently, the aim of this work was to create the computational model, bywhich means it will be possible to investigate the strength of described joint, thereby make the joint of required properties possible to design. The computational model was created in FEM system MSC.Marc, where the recently implemented failure criterion LaRC04 was used. The comparison of the numerical and experimental results shows that it is necessary to modify the criterion LaRC04. By means of the modified criterion LaRC04 it is possible to investigate the strength of the IHPJ joint in dependence onthe geometry or the material with good accuracy.
Klasifikace
Druh
Jx - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP obor
JI - Kompositní materiály
OECD FORD obor
—
Návaznosti výsledku
Projekt
Výsledek vznikl pri realizaci vícero projektů. Více informací v záložce Projekty.
Návaznosti
P - Projekt vyzkumu a vyvoje financovany z verejnych zdroju (s odkazem do CEP)
Ostatní
Rok uplatnění
2008
Kód důvěrnosti údajů
S - Úplné a pravdivé údaje o projektu nepodléhají ochraně podle zvláštních právních předpisů
Údaje specifické pro druh výsledku
Název periodika
Bulletin of Applied Mechanics
ISSN
1801-1217
e-ISSN
—
Svazek periodika
4
Číslo periodika v rámci svazku
13
Stát vydavatele periodika
CZ - Česká republika
Počet stran výsledku
6
Strana od-do
—
Kód UT WoS článku
—
EID výsledku v databázi Scopus
—
Základní informace
Druh výsledku
Jx - Nezařazeno - Článek v odborném periodiku (Jimp, Jsc a Jost)
CEP
JI - Kompositní materiály
Rok uplatnění
2008